Siemens SCALANCE XR524-8C Скачать руководство пользователя страница 18

Страница: 18 / 100

Description of the device

3.3 LED display

SCALANCE XR-500

Operating Instructions, 05/2014, A5E03275845-05

3.3

LED display

3.3.1

The "RM" LED for the "redundancy manager" function

The "RM" LED indicates whether or not the device is a redundancy manager and whether or

not the ring is operating free of error.

LED color

LED status

Meaning

Off

The device is not a redundancy manager.

Green

The device is a redundancy manager.
The ring is working without problems, monitoring is activated.

Green

Flashing

The device is a redundancy manager.
An interruption has been detected on the ring and the device

has switched through.

3.3.2

The "SB" LED for the standby function

The "SB" LED shows the status of the standby function.

LED color

LED status

Meaning

Off

The standby function is disabled.

Green

The standby function is enabled. The standby section is

passive.

Green

Flashing

The standby function is enabled. The standby section is active.

Содержание SCALANCE XR524-8C





































































































Результаты поиска

Содержание SCALANCE XR524-8C

Отзывы:

Похожие инструкции для SCALANCE XR524-8C

Бренды по названию

Популярные бренды

Siemens SCALANCE XR524-8C, Руководство по эксплуатации

Результаты поиска

Содержание SCALANCE XR524-8C

Отзывы:

Похожие инструкции для SCALANCE XR524-8C

Бренды по названию

Популярные бренды