Siemens SCALANCE XR524-8C Скачать руководство пользователя страница 19

Страница: 19 / 100

Description of the device

3.3 LED display

SCALANCE XR-500
Operating Instructions, 05/2014, A5E03275845-05

3.3.3

The "F" LED for the fault status

The "F" LED shows the fault/error status of the device.

Meaning during device startup

LED color

LED status

Meaning during device startup

Off

Device startup was completed successfully.

Red

Device startup is not yet completed or errors have occurred.

Red

Flashing

There are errors in the firmware.

Meaning during operation

LED color

LED status

Meaning during operation

Off

The device is operating free of errors.

Red

The device has detected a problem. The signaling contact has

opened.

3.3.4

"DM1" and "DM2" LEDs for the display mode

The "DM1" and "DM2" LEDs indicate which display mode is set.
There are 5 display modes (A, B, C, D, and E). Display mode A is the default mode.
Depending on the set display mode, the "L1", "L2" LEDs and the port LEDs show different

information.

LED color

LED status

Meaning

DM1 LED

DM2 LED

Off

Display mode A

Green

Off

Display mode B

Green

Off

Display mode C

Green

Display mode D

Green

Flashing

Off

Display mode E

Содержание SCALANCE XR524-8C





































































































Результаты поиска

Содержание SCALANCE XR524-8C

Отзывы:

Похожие инструкции для SCALANCE XR524-8C

Бренды по названию

Популярные бренды

Siemens SCALANCE XR524-8C, Руководство по эксплуатации

Результаты поиска

Содержание SCALANCE XR524-8C

Отзывы:

Похожие инструкции для SCALANCE XR524-8C

Бренды по названию

Популярные бренды