Siemens SCALANCE XR-500 Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 112

background image

Connecting

5.1 Commissioning

SCALANCE XR-500
Operating Instructions, 05/2017, A5E03275845-11

57

NOTICE
Failure of the data traffic due to contamination of optical plug-in connections
Optical sockets and plugs are sensitive to contamination of the end face. Contamination

can lead to the failure of the optical transmission network.
Close unused optical sockets and plugs as well as pluggable transceivers and slots with the

supplied protective caps.
Remove the protective caps only immediately before you use the plug-in connection.

Safety notices on use in hazardous areas

General safety notices relating to protection against explosion

WARNING

EXPLOSION HAZARD
Do not connect or disconnect cables to or from the device when a flammable or

combustible atmosphere is present.

Safety notices for use according to ATEX and IECEx
If you use the device under ATEX or IECEx conditions you must also keep to the following

safety notices in addition to the general safety notices for protection against explosion:

WARNING

Take measures to prevent transient voltage surges of more than 40% of the rated voltage.

This is the case if you only operate devices with SELV (safety extra-low voltage).

Safety notices when using the device according to Hazardous Locations (HazLoc)
If you use the device under HazLoc conditions you must also keep to the following safety

notices in addition to the general safety notices for protection against explosion:

WARNING

EXPLOSION HAZARD
You may only connect or disconnect cables carrying electricity when the power supply is

switched off or when the device is in an area without inflammable gas concentrations.

«
...
55
56
57
58
59
...
»

Содержание SCALANCE XR-500

















































































































Отзывы:

Нет отзывов

Похожие инструкции для SCALANCE XR-500

Бренд: SIMON RWA Страницы: 3

SkyEdge II-c Capricorn Pro 4 AC Series

Бренд: Gilat Страницы: 2

Бренд: socomec Страницы: 43

Бренд: netvox Страницы: 14

Бренд: Zamel Страницы: 2

Бренд: F&G Страницы: 6

Бренд: UniFi Страницы: 8

VH M 1 1 1 Series

Бренд: Jlso Tec Trade Страницы: 15

StorageWorks SAN Switch Integrated/32

Бренд: Compaq Страницы: 104

Crocodile Tail Loop

Бренд: One Control Страницы: 9

Бренд: Taiden Страницы: 21

SmartSTACK 100 ELS100-16TX

Бренд: Cabletron Systems Страницы: 16

Бренд: Contec Страницы: 38

Бренд: Hama Страницы: 36

Бренд: Hubner Страницы: 23

Бренд: Videosec Страницы: 3

IP Power 9258 DS

Бренд: Aviosys Страницы: 37

S5120-HI Series

Бренд: H3C Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды