Siemens SCALANCE XR-500 Скачать руководство пользователя страница 28

Страница: 28 / 112

Description of the device

3.3 LED display

SCALANCE XR-500

Operating Instructions, 05/2017, A5E03275845-11

3.3

LED display

3.3.1

The "RM" LED for the "redundancy manager" function

The "RM" LED indicates whether or not the device is a redundancy manager and whether or

not the ring is operating free of error.

LED color

LED status

Meaning

Off

The device is not a redundancy manager.

Green

The device is a redundancy manager.
The ring is working without problems, monitoring is activated.

Green

Flashing

The device is a redundancy manager.
An interruption has been detected on the ring and the device

has switched through.

3.3.2

The "SB" LED for the standby function

The "SB" LED shows the status of the standby function.

LED color

LED status

Meaning

Off

The standby function is disabled.

Green

The standby function is enabled. The standby section is pas-

sive.

Green

Flashing

The standby function is enabled. The standby section is active.

3.3.3

The "F" LED for the fault status

The "F" LED shows the fault/error status of the device.

Meaning during device startup

LED color

LED status

Meaning during device startup

Off

Device startup was completed successfully.

Red

Device startup is not yet completed or errors have occurred.

Red

Flashing

There are errors in the firmware.

Meaning during operation

LED color

LED status

Meaning during operation

Off

The device is operating free of errors. The signaling contact is

closed.

Red

The device has detected a problem. The signaling contact has

opened.

Содержание SCALANCE XR-500

















































































































Результаты поиска

Содержание SCALANCE XR-500

Отзывы:

Похожие инструкции для SCALANCE XR-500

Бренды по названию

Популярные бренды

Siemens SCALANCE XR-500, Руководство по эксплуатации

Результаты поиска

Содержание SCALANCE XR-500

Отзывы:

Похожие инструкции для SCALANCE XR-500

Бренды по названию

Популярные бренды