Siemens SCALANCE XR-500 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 112

background image

Assembling

4.1 Safety notices for installation

SCALANCE XR-500

38

Operating Instructions, 05/2017, A5E03275845-11

NOTICE
Damage to the device due to inadequate cooling
If the ventilation slits are fully or partly covered, the temperature inside the housing can rise

and exceed the maximum permitted temperature causing damage to the device.
The ventilation slits are located on the side panels of the housing. During installation, select

a mounting position so that the ventilation slits are always free so that the air can circulate.

The clearance to the ventilation slits of the housing must be at least 10 cm.
You will find information about cleaning the air filter in the section "Upkeep and

maintenance".
Close unused module slots of modular devices with dummy covers. Open module slots

impair the air circulation and can damage the device.
If you mount a SCALANCE XR524-8C or SCALANCE XR526-8C in a rack, leave at least

one height unit free above and below.

NOTICE
Warming and premature aging of the IE switch due to direct sunlight
Direct sunlight can heat up the device and can lead to premature aging of the IE switch and

its cabling.
Provide suitable shade to protect the IE switch against direct sunlight.

Note
During installation and operation, keep to the installation guidelines and safety notices

described in this document and in the system manuals "Industrial Ethernet / PROFINET

Industrial Ethernet" and "Industrial Ethernet / PROFINET passive network components".
You will find information on the system manuals in the section "Introduction (Page 5)", in

"Further documentation".

Safety notices on use in hazardous areas

General safety notices relating to protection against explosion

WARNING

EXPLOSION HAZARD
Replacing components may impair suitability for Class 1, Division 2 or Zone 2.

WARNING

The device is intended for indoor use only.

«
...
36
37
38
39
40
...
»

Содержание SCALANCE XR-500

















































































































Отзывы:

Нет отзывов

Похожие инструкции для SCALANCE XR-500

Бренд: E-T-A Страницы: 6

Бренд: NETGEAR Страницы: 36

Бренд: Ableconn Страницы: 16

Бренд: CYP Страницы: 32

Бренд: Xantech Страницы: 4

Бренд: I-Tech Страницы: 39

PMV WM Ultraswitch

Бренд: Flowserve Страницы: 16

Бренд: Fairchild Страницы: 20

Бренд: Televes Страницы: 24

CEFLA PIR DALIP

Бренд: DANLERS Страницы: 2

InSwitch ISM-P Series

Бренд: InHand Страницы: 81

Бренд: Exsys Страницы: 14

Бренд: Black Box Страницы: 132

AVS-OP-2404-210

Бренд: AMX Страницы: 1

Бренд: Kraun Страницы: 8

Бренд: SP Controls Страницы: 24

Бренд: Planet Networking & Communication Страницы: 16

Бренд: Upvel Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды