Siemens SCALANCE M804PB Скачать руководство пользователя страница 29

Страница: 29 / 68

Installation

4.1 Securing the housing

SCALANCE M804PB
Operating Instructions, 07/2018, C79000-G8976-C496-01

4.1

Securing the housing

Types of installation

For the device, you have the following options:

●

Wall mounting (no ceiling mounting)

●

Installation on a DIN rail

●

Installing on the S7-300 standard rail

●

Installing on the S7-1500 standard rail

●

Mounting on a pedestal

Strain relief for the cables
Regardless of the type of installation, make sure that there is suitable strain relief for the

connecting cable.

Shielding of cables
If cables are installed permanently, it is advisable to remove the insulation of the shielded

cable and to establish contact on the shield/PE conductor bar.

Permitted installation direction

●

Vertical installation (ventilation openings at the top and bottom)

Clearances
Keep to the minimum clearances to other components or to walls of a housing so that the

convection ventilation of the device is not blocked.

●

Below at least 10 cm

●

Above at least 10 cm

Содержание SCALANCE M804PB





































































Результаты поиска

Содержание SCALANCE M804PB

Отзывы:

Похожие инструкции для SCALANCE M804PB

Бренды по названию

Популярные бренды

Siemens SCALANCE M804PB, Руководство по эксплуатации

Результаты поиска

Содержание SCALANCE M804PB

Отзывы:

Похожие инструкции для SCALANCE M804PB

Бренды по названию

Популярные бренды