Siemens SCALANCE M804PB Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 68

background image

SCALANCE M804PB
Operating Instructions, 07/2018, C79000-G8976-C496-01

15

Safety notices

2

CAUTION

To prevent injury, read the manual before use.

Read the safety notices

Note the following safety notices. These relate to the entire working life of the device.
You should also read the safety notices relating to handling in the individual sections,

particularly in the sections "Installation" and "Connecting up".

WARNING

The device is intended for indoor use only.

WARNING

Suitable cables at high ambient temperatures
If the temperature of the cable or housing socket exceeds 70 °C or the branching point of

conductors exceeds 80 °C, special precautions must be taken.
If the device is operated at ambient temperatures of between 50 °C and 70 °C, only use

cables with a maximum permitted operating temperature of at least 80 °C.

Safety notices on use in hazardous areas

General safety notices relating to protection against explosion

WARNING

EXPLOSION HAZARD
DO NOT OPEN WHEN ENERGIZED.

Safety notices when using the device according to Hazardous Locations (HazLoc) and FM.
If you use the device under HazLoc or FM conditions you must also keep to the following

safety notices in addition to the general safety notices for protection against explosion:
This equipment is suitable for use in Class I, Division 2, Groups A, B, C and D or non-

hazardous locations only.
This equipment is suitable for use in Class I, Zone 2, Group IIC or non-hazardous locations

only.

«
...
13
14
15
16
17
...
»

Содержание SCALANCE M804PB





































































Отзывы:

Нет отзывов

Похожие инструкции для SCALANCE M804PB

Бренд: RAMSET Страницы: 16

Бренд: Wacker Neuson Страницы: 54

Бренд: Jet Страницы: 20

Бренд: Jet Страницы: 28

Бренд: Wacker Neuson Страницы: 48

Бренд: IGM Professional Страницы: 56

Бренд: Gardner Denver Страницы: 27

Бренд: Fervi Страницы: 6

Бренд: BGS technic Страницы: 4

Бренд: Bullet tools Страницы: 10

Бренд: Milwaukee Страницы: 55

Бренд: Jarvis Страницы: 12

Бренд: Bomag Страницы: 58

Бренд: TDK-Lambda Страницы: 18

Бренд: Fein Страницы: 31

Бренд: Tactical Страницы: 4

Бренд: Black Box Страницы: 2

Бренд: HAMPTON BAY Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды