Siemens SATURN IIE, Процедуры испытаний при установке

Страница: 42 / 55

SATURN EPABX
Test Procedures Issue 1, May 1986
6.04 Pad Test
S T E P VERIFICATION
IS NOT OBTAINED
7 Depress the DTMF keypad buttons in
Recall dial tone ceases. After all the If busy tone is returned at any time,
the following sequence:
buttons are depressed e i t h e r t h e D T M F k e y p a d b u t t o n s w e r e
in the sequence indicated, test tone depressed in the wrong
For phones: 1, 2, 3, 4, 5, 6, -16dBm) is returned for
D T M F k e y p a d o f t h e s t a t i o n u n d e r t e s t
8, 9, 0, and one minute.
is defective or the subscriber line cir-
cuit is defective.
For 16-button phones: A, B, C, D, 1,
2, 3, 4, 5, 6, 7, 8, 9, 0, and
T o l o c a t e f a i l u r e , r e t r y t e s t t o v e r i f y t h a t
t h e k e y p a d b u t t o n s w e r e n o t
d e p r e s s e d o u t o f s e q u e n c e . I f
problem persists, swap the station in-
s t r u m e n t t o d e t e r m i n e
i t i s d e f e c t i v e .
If problem remains, replace the
propriate subscriber line PCB.
8 level of test tone by using
If the measured test tone is correct
but is weak, replace the station set.
If the measured tone is low,
the subscriber line PCB SLMA or
9 Place DTMF station under test on- N o n e .
hook to terminate test.
1 0 If no additional apparatus tests are to
be performed, proceed as foilows:
Place maintenance test phone Dial tone is returned.
D i a l t h e D i a g n o s t i c T e s t A c c e s s C o d e . Recall dial tone is returned.
Dial 2 to disable the Apparatus Tests. N o n e .
P l a c e m a i n t e n a n c e t e s t p h o n e N o n e .
on-hook.
Table 6.05 Console Test
N O T E S : 1 ) If the system option flag TSTDIAG has been enabled in the data base, the maintenance test phone is not required
to enable and disable the Apparatus Test routines; therefore, perform only steps 5 through 9.
2) If the system option flag TSTDIAG has been in the data base, the maintenance test phone is required
to enable and disable the Apparatus Test routines; therefore, perform the entire procedure (steps 1 through 10).
S T E P PROCEDURE VERIFICATION IF VERIFICATION
IS NO-i- OBTAINED
1 Place maintenance test phone Dial tone is returned.
off-hook.
2 D i a l t h e D i a g n o s t i c T e s t A c c e s s C o d e . Recall dial tone is returned.
3
Dial 3 to enable the Apparatus Tests.
Confirmation tone is returned.
4
P l a c e m a i n t e n a n c e t e s t p h o n e N o n e .
on-hook.
5
At the Console under test dial the Recall dial tone is returned. Also the
If reorder tone is returned, the
Console Test access code access code is displayed dant Console Test routine is in use,
when the console is in an idle state.
ily, then the display changes to CON- retry later.
SOLE TEST and all button
are
extinguished.
6 - 1 6