Siemens RUGGEDCOM WIN5114 Скачать руководство пользователя

Страница: 5 / 32

RUGGEDCOM WIN5114-V

Installation Guide

Preface

Alerts

Preface

This guide describes the RUGGEDCOM WIN5114-V. It describes the major features of the subscriber unit,

installation, commissioning and important technical specifications.
It is intended for use by subscriber unit installers and operators, and assumes readers have a working knowledge

of WiMAX technologies and procedures. While some safety precautions are reviewed here, it is assumed that

installers are trained in safe installation practices. Users unfamiliar with safe installation procedures, WiMAX

technologies, and service procedures should not rely on this manual for comprehensive guidance.

CONTENTS

•

•

•

•

Alerts

The following types of alerts are used when necessary to highlight important information.

DANGER!

DANGER alerts describe imminently hazardous situations that, if not avoided, will result in death or

serious injury.

WARNING!

WARNING alerts describe hazardous situations that, if not avoided, may result in serious injury and/or

equipment damage.

CAUTION!

CAUTION alerts describe hazardous situations that, if not avoided, may result in equipment damage.

IMPORTANT!

IMPORTANT alerts provide important information that should be known before performing a procedure

or step, or using a feature.

NOTE

NOTE alerts provide additional information, such as facts, tips and details.

Содержание RUGGEDCOM WIN5114

































Результаты поиска

Содержание RUGGEDCOM WIN5114

Отзывы:

Похожие инструкции для RUGGEDCOM WIN5114

Бренды по названию

Популярные бренды

Siemens RUGGEDCOM WIN5114, Руководство по установке

Результаты поиска

Содержание RUGGEDCOM WIN5114

Отзывы:

Похожие инструкции для RUGGEDCOM WIN5114

Бренды по названию

Популярные бренды