Siemens RUGGEDCOM WIN5114 Скачать руководство пользователя

Страница: 11 / 32

RUGGEDCOM WIN5114-V

Installation Guide

Chapter 2

Installing the Subscriber Unit

Installing the Subscriber Unit

This chapter describes how to install the subscriber unit, including mounting the subscriber unit, connecting

power, connecting the antenna, and connecting the subscriber unit to the network.

DANGER!

Electrocution hazard – risk of serious personal injury and/or damage to equipment. Before performing

any maintenance tasks, make sure all power to the subscriber unit has been disconnected and wait

approximately two minutes for any remaining energy to dissipate.

DANGER!

Electrocution hazard – risk of death or serious injury. When the subscriber unit is installed in an

outdoor location, all indoor components (e.g. Ethernet and power supply) should be connected

through a lightning protector.
Lightning protection protects people and equipment located indoors from lightning that may strike

the subscriber unit or its outdoor cables. Therefore, install the lightning protector indoors, as close

as possible to the point where the cables enter the building. The lightning protector can also be

installed outdoors as long as the cables that lead indoors are well protected from lightning between

the protector and the building entrance.

WARNING!

Safety hazard – risk of serious personal injury and/or damage to equipment. Installing the

RUGGEDCOM WIN5114-V can pose a serious safety hazard. Be sure to take precautions to avoid the

following:
• Exposure to high voltage lines during installation
• Falling when working at heights or with ladders
• Injuries from dropping tools
• Contact with AC wiring (power system connection)

IMPORTANT!

Only certified personnel should be permitted to install equipment.

IMPORTANT!

This product contains no user-serviceable parts. Attempted service by unauthorized personnel shall

render all warranties null and void.
Changes or modifications not expressly approved by Siemens Canada Ltd could invalidate

specifications, test results, and agency approvals, and void the user's authority to operate the

equipment.

Содержание RUGGEDCOM WIN5114

































Результаты поиска

Содержание RUGGEDCOM WIN5114

Отзывы:

Похожие инструкции для RUGGEDCOM WIN5114

Бренды по названию

Популярные бренды

Siemens RUGGEDCOM WIN5114, Руководство по установке

Результаты поиска

Содержание RUGGEDCOM WIN5114

Отзывы:

Похожие инструкции для RUGGEDCOM WIN5114

Бренды по названию

Популярные бренды