Siemens RUGGEDCOM WIN5114 Скачать руководство пользователя

Страница: 26 / 32

Chapter 4

Technical Specifications

RUGGEDCOM WIN5114-V

Installation Guide

Operating Environment

7 MHz
10 MHz

Frequency Resolution

250 kHz

Transmission Mode for MIMO

MRC/STC (downlink)

Antenna Type

External RF

Number of Ports for External

Antenna(s)

Type of Ports for External

Antenna(s)

N-Connect female

Maximum Transmit Power

0.5 W

Transmit Power Level

(Adjustable)

54 dB

Size of Fast Fourier Transform

(FFT) Channels

1024/512FFT

Type of Modulation

QPSK, 16-QAM, 64-QAM

Dynamic Range (Receiver)

-20 to 100 dBm

Dynamic Range (Transmitter)

-20 to 27 dBm

Section 4.4

Operating Environment

The RUGGEDCOM WIN5114-V is rated to operate under the following environmental conditions.

Ambient Operating

Temperature

-40 to 75 °C (-40 to 167 °F)

Ambient Storage Temperature

-40 to 75 °C (-40 to 167 °F)

Ambient Relative Humidity

5% to 95%

Maximum Altitude

2000 m (6562 ft)

Measured from a 30 cm (12 in) radius surrounding the center of the enclosure

Non-condensing

Section 4.5

Mechanical Specifications

Weight

1.5 kg (3.3 lb)

Ingress Protection

IP67

Enclosure

Aluminum

Содержание RUGGEDCOM WIN5114

































Результаты поиска

Содержание RUGGEDCOM WIN5114

Отзывы:

Похожие инструкции для RUGGEDCOM WIN5114

Бренды по названию

Популярные бренды

Siemens RUGGEDCOM WIN5114, Руководство по установке

Результаты поиска

Содержание RUGGEDCOM WIN5114

Отзывы:

Похожие инструкции для RUGGEDCOM WIN5114

Бренды по названию

Популярные бренды