Siemens RUGGEDCOM RX1501 Скачать руководство пользователя страница 14

Страница: 14 / 68

Installing the Device

This chapter describes how to install the device, including mounting the device, con-

necting power, and connecting the device to the network.

DANGER

Electrocution hazard – risk of serious personal injury and/or damage to equip-

ment.

Before performing any maintenance tasks, make sure all power to the device has

been disconnected and wait approximately two minutes for any remaining energy

to dissipate.

WARNING

Radiation hazard – risk of serious personal injury.

This product contains a laser system and is classified as a

CLASS 1 LASER PRODUCT

Use of controls or adjustments or performance of procedures other than those speci-

fied herein may result in hazardous radiation exposure.

WARNING

Radiation hazard – risk of Radio Frequency (RF) exposure.

This device is compliant with the requirements set forth in FCC 47 CFR, section

1.1307, addressing Radio Frequency (RF) exposure from radio frequency base sta-

tions, as defined in

FCC OET Bulletin 65 [http://transition.fcc.gov/Bureaus/Engi-

neering_Technology/Documents/bulletins/oet65/oet65.pdf]

. The emitted radiation

should be as little as possible. To achieve minimum RF exposure, install the device

when it is configured not to transmit and set it to operational mode remotely, rather

than having a technician enable transmission on-site. For maintenance of the base

station, or other operations which require RF exposure, the exposure should be min-

imized in time and according to the regulations set forth by the country of installa-

tion or the Federal Communications Commission (FCC).

IMPORTANT

This product contains no user-serviceable parts. Attempted service by unauthorized

personnel shall render all warranties null and void.
Changes or modifications not expressly approved by Siemens AG could invalidate

specifications, test results, and agency approvals, and void the user's authority to

operate the equipment.

IMPORTANT

RUGGEDCOM RX1501

Installation Manual, 05/2020, C79000-G8976-1054-17

All manuals and user guides at all-guides.com

Содержание RUGGEDCOM RX1501





































































Результаты поиска

Содержание RUGGEDCOM RX1501

Отзывы:

Похожие инструкции для RUGGEDCOM RX1501

Бренды по названию

Популярные бренды

Siemens RUGGEDCOM RX1501, Руководство по установке

Результаты поиска

Содержание RUGGEDCOM RX1501

Отзывы:

Похожие инструкции для RUGGEDCOM RX1501

Бренды по названию

Популярные бренды