background image

 

Table of Contents

RUGGEDCOM RST2228

Installation Guide

iv

Chapter 4

Communication Ports ...................................................................................... 

25

4.1  SFP Transceivers .........................................................................................................................  25
4.2  Available Modules ....................................................................................................................... 27
4.3  Installing/Removing Modules .......................................................................................................  28

Chapter 5

Technical Specifications ..................................................................................  

31

5.1  Power Supply Specifications ........................................................................................................  31
5.2  Failsafe Alarm Relay Specifications ...............................................................................................  32
5.3  Supported Networking Standards ................................................................................................. 32
5.4  Operating Environment ...............................................................................................................  32
5.5  Mechanical Specifications ............................................................................................................ 33
5.6  Dimension Drawings ...................................................................................................................  33

Chapter 6

Certification ....................................................................................................  

37

6.1  Approvals ...................................................................................................................................  37

6.1.1  CSA ................................................................................................................................. 37
6.1.2  European Union (EU) .......................................................................................................  38
6.1.3  FCC .................................................................................................................................  39
6.1.4  FDA/CDRH ........................................................................................................................ 39
6.1.5  ISED ................................................................................................................................  39
6.1.6  TÜV SÜD .........................................................................................................................  39
6.1.7  RoHS ............................................................................................................................... 39
6.1.8  Other Approvals ............................................................................................................... 40

6.2  EMC and Environmental Type Tests .............................................................................................. 40

Содержание RUGGEDCOM RST2228



















































Отзывы: