Siemens RUGGEDCOM RST2228 Скачать руководство пользователя страница 33

Страница: 33 / 50

RUGGEDCOM RST2228

Installation Guide

Chapter 4

Communication Ports

Available Modules

SFP Transceiver

Order Code

Speed

(Mbit/s)

Mode

Nominal Distance (km)

RUGGEDCOM SFP2133-1ZR80

6GK6000-8FT52-0AA0

10000

MM = Multi-Mode, SM = Single-Mode

Only compatible with SFP/SFP+ Transceiver Sockets.

Not compatible with SFP/SFP+ Transceiver Sockets.

Section 4.2

Available Modules

The following modules are available for use with the RUGGEDCOM RST2228. For more information about

individual modules, refer to the

RUGGEDCOM Modules Catalog

for the device available online.

Copper Ethernet Modules

RUGGEDCOM RMM2973-4RJ45

Specifications

Ports: 4
Port Type: RJ45
Speed: 10/100/1000 Mbps
Interface: TX
Distance: 100 m (328 ft)

Article Numbers

6GK6297-3RD00-4AB0

(Standard)
6GK6297-3RD00-4AB1

(Conformal Coated)

RUGGEDCOM RMM2973-4FC

Specifications

Ports: 4
Port Type: FastConnect RJ45
Speed: 10/100/1000 Mbps
Interface: TX
Distance: 100 m (328 ft)

Article Numbers

6GK6297-3FD00-4AB0

(Standard)
6GK6297-3FD00-4AB1

(Conformal Coated)

Fiber Optic Ethernet Modules

RUGGEDCOM RMM2972-4SFP

Specifications

SFP Sockets: 4
Speed: 100/1000 Mbps

Article Numbers

6GK6297-2SA00-4AA0

(Standard)
6GK6297-2SA00-4AA1

(Conformal Coated)

RUGGEDCOM RMM2942-4LC2

Specifications

Ports: 4
Port Type: LC
Mode: MM (Multi-Mode)
Speed: 100 Mbps
Interface: FX
Wavelength: 1310 nm
Distance: 2 km (1.2 mi)

Article Numbers

6GK6294-2LD00-4AC0

(Standard)
6GK6294-2LD00-4AC1

(Conformal Coated)

Содержание RUGGEDCOM RST2228



















































Результаты поиска

Содержание RUGGEDCOM RST2228

Отзывы:

Похожие инструкции для RUGGEDCOM RST2228

Бренды по названию

Популярные бренды

Siemens RUGGEDCOM RST2228, Руководство по установке

Результаты поиска

Содержание RUGGEDCOM RST2228

Отзывы:

Похожие инструкции для RUGGEDCOM RST2228

Бренды по названию

Популярные бренды