Siemens RUGGEDCOM RS900F Скачать руководство пользователя страница 42

Страница: 42 / 48

Chapter 6

Certification

RUGGEDCOM RS900F

Installation Guide

CSA/Sira

•

CAN/CSA-C22.2 No. 213-M1987

Non-Incendive Electrical Equipment for Use in Class I, Division 2 Hazardous Locations

•

CAN/CSA-C22.2 No. 60079-0:11

Explosive Atmospheres – Part 0: Equipment – General Requirements

•

CAN/CSA-C22.2 No. 60079-15:12

Electrical Apparatus for Explosive Gas Atmospheres – Part 15: Construction, Test and Marking of Type of

Protection "n" Electrical Apparatus

•

UL 60079-0, Edition 6.0 (2013)

Explosive Atmospheres – Part 0: Equipment – General Requirements

•

UL 60079-15, Edition 4.0 (2013)

Explosive Atmospheres – Part 15: Equipment Protection by Type of Protection "n"

•

ANSI/ISA-12.12.01-2013

Non-Incendive Electrical Equipment for Use in Class I and II, Division 2 and Class III, Division 1 and 2 Hazardous

(Classified) Locations

The device is marked with a CSA symbol that indicates compliance with both Canadian and U.S. requirements.

It is specifically approved for use in hazardous locations with the following markings:
• Class I, Division 2, Groups A, B, C, D T4
• Ex nA nC IIC T4 Gc
• Class I, Zone 2, AEx nA nC IIC T4 Gc

Section 6.1.2

CSA/Sira

When marked with the following ATEX marking, this device is approved for use in hazardous locations under

certificate Sira 15ATEX4262X.

NOTE

For the maximum ambient temperature, refer to the hazardous location label affixed to the device.

II 3 G Ex nA nC IIC T4 Gc

The device also meets the requirements of the following CSA/Sira standards:
•

2014/34/EU

Directive 2014/34/EU of the European Parliament and of the Council of 26 February 2014 on the harmonisation

of the laws of the Member States relating to equipment and protective systems intended for use in potentially

explosive atmospheres (recast) Text with EEA relevance

•

IEC 60079-0, Edition 6.0 (2011)/EN 60079-0:2012/A11:2013

Explosive Atmospheres – Part 0: Equipment – General Requirements

Содержание RUGGEDCOM RS900F

















































Результаты поиска

Содержание RUGGEDCOM RS900F

Отзывы:

Бренды по названию

Популярные бренды

Siemens RUGGEDCOM RS900F, Руководство по установке

Результаты поиска

Содержание RUGGEDCOM RS900F

Отзывы:

Бренды по названию

Популярные бренды