manualshive.com logo in svg

Siemens RUGGEDCOM RS900F, Руководство по установке

Поделиться
Скачать
Siemens RUGGEDCOM RS900F Скачать руководство пользователя страница 33

RUGGEDCOM RS900F

Installation Guide

Chapter 4

Communication Ports

Fiber Optic Ethernet Ports

23

Section 4.2

Fiber Optic Ethernet Ports

Fiber optic Ethernet ports are available with either MTRJ (Mechanical Transfer Registered Jack), LC (Lucent

Connector), SC (Standard or Subscriber Connector) or ST (Straight Tip) connectors. Make sure the Transmit (Tx)

and Receive (Rx) connections of each port are properly connected and matched to establish a proper link.

Port Types

2

1

Figure 14: MTRJ Port

1.

 Tx Connector   

 

2.

 Rx Connector

2

1

Figure 15: LC Port

1.

 Tx Connector   

 

2.

 Rx Connector

2

1

Figure 16: SC Port

1.

 Tx Connector   

 

2.

 Rx Connector

2

1

Figure 17: ST Port

1.

 Tx Connector   

 

2.

 Rx Connector

LEDs

Each port features an LED that indicates the link/activity state of the port.

State

Description

Yellow (Solid)

Link established

Yellow (Blinking)

Link activity

Off

No link detected

Specifications

For specifications on the available fiber optic Ethernet ports, refer to 

Section 5.4, “Fiber Optic Ethernet Port

Specifications”

.

Содержание RUGGEDCOM RS900F

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды