manualshive.com logo in svg

Siemens RUGGEDCOM RS900F, Руководство по установке

Поделиться
Скачать
Siemens RUGGEDCOM RS900F Скачать руководство пользователя страница 21

RUGGEDCOM RS900F

Installation Guide

Chapter 2

Installing the Device

Mounting the Device to a Panel

11

1

1

2

Figure 3: DIN Rail Mounting

1.

 DIN Rail   

 

2.

 DIN Rail Bracket

2. Pull the release on the bracket down and slide the device onto the DIN rail. Let go of the release to lock the

device in position. If access to the release is limited, use a slotted screwdriver or a similar tool to reach the

release.

Section 2.4.2

Mounting the Device to a Panel

For panel installations, the RUGGEDCOM RS900F can be equipped with panel adapters pre-installed on the top and

bottom of the chassis. The adapters allow the device to be attached to a panel using screws.
To mount the device to a panel, do the following:
1. Prepare mounting holes in the panel where the device is to be installed.
2. Place the device against the panel and align the adapters with the mounting holes.

Содержание RUGGEDCOM RS900F

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды