Siemens NK8222 Скачать руководство пользователя страница 35

Страница: 35 / 90

Hardware installation

NE8000 cabinets

Building Technologies

A6V10062437_a_en

Fire Safety & Security Products

30.06.2013

The VAC power supply wires (1.5 mm

) should be connected as illustrated in Figure

VAC power connection.

WARNING

Careful attention should be paid to the correct connections of VAC power lines.

Ground

Phase

Neutral

Input VAC
1.5 mm

wires

VAC power connection

Wires pass through 20 mm (cut-out) holes at the top of the cabinet (see Figure

Top

view of NE8000 cabinet), and continue behind the cabinet to pass through the rear-

side cavity to the entrance hole (see Figure

Wiring (1) – Front view of cabinet (arrow

indicates cut-out holes) and Figure Wiring (2) – Entrance hole indicated by arrow)

where they should be anchored securely before being connected to the screw

terminators.

20 mm hole cut-outs

Top view of NE8000 cabinet

Содержание NK8222



























































































Результаты поиска

Содержание NK8222

Отзывы:

Siemens NK8222, Инструкция по установке, функционированию и настройке, правила безопасности при вводе в эксплуатацию, Страница: 35 / 90

Результаты поиска

Содержание NK8222

Отзывы: