Siemens NK8222 Скачать руководство пользователя страница 26

Страница: 26 / 90

Structure and functions

NK823x hardware

26
Building Technologies

A6V10062437_a_en

Fire Safety & Security Products

30.06.2013



Blinking (2 flashes): trouble with the I

C bus to I/O modules.



Blinking (3 flashes): not used



Blinking (4 flashes): trouble with the serial/network interface.



Blinking (5 flashes): trouble with DLL or RCLOCK file(s).



Blinking (6 flashes): Modbus GW trouble.
–  SW trouble.
–  No communication to FS20/FS720 or to the Modbus Master/Client.
–  No NK8237 or FS20/FS720 registers reading (Modbus Master watchdog

expired).



On: critical/hardware fault.

Right Side LED’s

The four LED's on the right side are, from top to bottom:

Name

Function

Com1

Status Com1

Com2

Status Com2

Com3

Status Com3

Com4

Status Com4

Red: RX

Green: TX

4.2.2

Internal DIP switches

The internal DIP switches (S101) enable a download session via FTP using a default

IP address.

Internal switch

Functions

DIP switch 1

Default mode/network access: If DIP-switch 1 is ON, an FTP connection occurs

by default on the Ethernet at the default IP address 192.168.9.41.

DIP switch 2

Default mode/network access: If DIP-switch 2 is ON, an FTP connection occurs

by default on the Ethernet at the default IP address 192.168.10.41.

Содержание NK8222



























































































Результаты поиска

Содержание NK8222

Отзывы:

Бренды по названию

Популярные бренды

Siemens NK8222, Инструкция по установке, функционированию и настройке, правила безопасности при вводе в эксплуатацию

Результаты поиска

Содержание NK8222

Отзывы:

Бренды по названию

Популярные бренды