Siemens NK8222 Скачать руководство пользователя страница 31

Страница: 31 / 90

Structure and functions

NK823x hardware

Building Technologies

A6V10062437_a_en

Fire Safety & Security Products

30.06.2013

Note: Locally connected DF8000 I/O modules are only supported with NK823x with

build state 10 or higher (NKM8001-A2 mainboard).

For more information about the DF8000 Input/Output modules, including installation

details, see documents

DF8000 Datasheet (document no.A6V10081184) and DF8000

ICC (document no.A6V10081388).

4.2.8

Ethernet interfaces

The NK823x main board is equipped with two Ethernet interfaces. The two RJ-45

connectors also include 2 LEDs (yellow and green) reporting the LAN status as follows:



Yellow LED: if on, a 100 Mbps link is active.



Green LED: flashing when data is received or transmitted.

Back

Ethernet connectors

Item

Description

Ethernet 1

Ethernet 2

4.2.9

USB interface

The NK823x main board is equipped with a USB interface you can use to log data

about network communications on a USB mass storage device (see

Network

Connectivity Guide, document no.A6V10359485).

Содержание NK8222



























































































Результаты поиска

Содержание NK8222

Отзывы:

Похожие инструкции для NK8222

Бренды по названию

Популярные бренды

Siemens NK8222, Инструкция по установке, функционированию и настройке, правила безопасности при вводе в эксплуатацию

Результаты поиска

Содержание NK8222

Отзывы:

Похожие инструкции для NK8222

Бренды по названию

Популярные бренды