manualshive.com logo in svg
  • Главная
  • /
  • Siemens
  • /
  • NK8222
  • /
  • Инструкция по установке, функционированию и настройке, правила безопасности при вводе в эксплуатацию

Siemens NK8222, Инструкция по установке, функционированию и настройке, правила безопасности при вводе в эксплуатацию

Поделиться
Скачать
Siemens NK8222 Скачать руководство пользователя страница 12

Introduction 

2 

Interactions 

12 
Building Technologies 

 

A6V10062437_a_en

Fire Safety & Security Products 

 

30.06.2013

2.1

 

Interactions 

The unit can be programmed to support interactions between the connected 

subsystems: when a specified message is received from a source subsystem, one or 

more commands are generated for a destination subsystem according to the 

programmed interaction logic. 
Interactions can be 

local or network-wide: 

  Local interactions only involve the subsystems connected to a single unit. 

  Network-wide interactions involve subsystems connected on different units, which 

coordinate the interaction task over the network. Network-wide interactions require 

units supporting the BACnet protocol. 

 

 

Note: NK8000 units are not certified as part of an EN54-2 fire detection system. 

Therefore, the interactions should only be used in applications where they are not in 

conflict with EN54 standards or national guidelines or regulations (e.g. not for 

common control of remote transmission devices). 

 

 

 

Note: NK8231 and NK8237 do not support interactions. 

Both local and network-wide interactions are supported for a restricted list of 

subsystems: 

  FS20 Sinteso Fire control units (this subsystem is not supported by NK822x) 

  FS720 Cerberus Pro Fire control units (this subsystem is not supported by 

NK822x) 

  STT20 Fire control unit (this subsystem is not supported by NK822x) 

  CS11 AlgoRex

® 

Fire control unit 

  CS1115 Fire control unit 

  FC330A Fire control unit 

  FC700A Fire control unit 

  SIGMASYS/D100 Fire control unit 

  XLS FireFinder control unit 

  CS6 Guarto Intrusion control unit 

  SI410 Intrunet (formerly Sintony) Intrusion control unit 

  DF8000/CF9000 I/O modules 

  MK7022 Cerloop Interface 

  Philips Burle CCTV switcher 

For details on interactions, see the 

Network Connectivity Guide (document 

no.A6V10359485). 

Содержание NK8222



























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды