manualshive.com logo in svg

Siemens MD-P1, Руководство пользователя, Страница: 64 / 76

Поделиться
Скачать
Siemens MD-P1 Скачать руководство пользователя страница 64

 

Appendices 

Appendix F - Measuring Consumption (kWh), Demand, and Other Applications 

 

64 

Siemens Industry, Inc. 

 

125-201 

 

 

09/30/2019 

 

Another variation of these applications is to create a PPCL which captures energy 
consumption (for example, daily, hourly) in a single virtual point. This virtual point can 
be trended and building operators can use the Insight Dynamic Plotter to monitor 
dynamic and/or historical energy consumption. 

NOTES:

 

1. 

The slope and intercepts of %X%CMH and %X%CML are the same as 
accumulator points (%Z%, %Y%).  

2. 

The slope (that is, resolution) for monthly readings should be determined by 
identifying the maximum billed consumption or using the following equations 
(assume PF = 1.0): 

kWref = (CTref. Amps × Voltsref)/1000 

for 1-Phase Power 

kWref = (CTref. Amps × Voltsref × SQRT(3) × PF)/1000 

for 3-Phase Power 

kWh = kWref * 24 hours/day × 31 Days 

for kWh per Month 

kWh = kWref * 24 hours/day × 7 Days 

for kWh per Week 

 

 

●  For firmware revisions earlier than 2.0, do not use the $LOC resident point for 

intermediate calculations; the maximum value of the $LOC resident point is 32,767. 

 

Maximum  

Physical Unit (V2) 

Slope 

(Resolution) 

Intercept 

(V1) 

32,766.00 

1 

0 

327,660.00 

10 

0 

163.83 

0.05 

0 

1638.30 

0.5 

0 

163,830 

5 

0 

1,638,300 

50 

0 

32,766.00 

1 

0 

 

 

Measuring and Calculating Demand (kW) 

DEMAND represents the instantaneous 3-phase total demand (kW) and functions as a 
logical analog input. In applications where the demand fluctuates, increase the COV 
parameter for DEMAND to reduce COV traffic. If the power meter is reading whole 
building kW, the largest number of COVs occurs when the building transitions from 
unoccupied to occupied status. For example, using a 300A power meter with a COV 
limit of 0.064 results in changes of values being observed for every change greater 
than 0.064 kW (such as every time a 1.0 HP motor, one 100W light bulb, or a personal 
computer is energized). 

In general, select the COV for the kW based on the range of the CT. For example, if a 
1% COV is needed for a 300 Amp service (300 Amps × Sqrt (3) × 480V/1000 = 249.6 
kW ), select a COV of the slope × 20 (provides a COV every 0.064 slope × 20 kW = 

Содержание MD-P1













































































Отзывы:

Нет отзывов