Siemens MD-P1 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 76

Siemens MD-P1 Скачать руководство пользователя страница 11

Introduction

Safety Summary and Specifications

11

Siemens Industry, Inc.

125-201

09/30/2019

Symboles sur l’appareil

CAUTION

Signifie prudence.

Le dommage d'équipement ou la perte de données peuvent se produire si vous ne
suivez pas de procédure comme spécifié.

WARNING

Indique une haute tension.

Risque de choc électrique. Des tensions mettant en danger la vie des personnes
peuvent être présentes. Personnel qualifié uniquement.

CAUTION

Ce compteur peut contenir des tensions pouvant mettre en danger la vie des
personnes.

Un personnel doit débrancher les câbles de haute tension avant d’utiliser ou de
dépanner le compteur.

WARNING

Ne pas utiliser cet appareil à des fins autres que celles indiquées.

Tout autre utilisation peut annuler ses moyens de protection.

WARNING

Risque d’électrocution

Pour raccorder un MD Model Power Meter à une prise de courant alternatif, suivez
cette séquence pour empêcher tout risque l’électrocution.
●  Mettez hors tension le circuit à surveiller.
●  Connectez le transformateur de courant aux phases à surveiller.
●  Connectez les fils de tension aux différentes phases. Utiliser des équipements de

protection (gants et des vêtements de protection) nécessaires pour les tensions
surveillées.

WARNING

Ne pas dépasser 600 V.

Ce compteur peut contrôler des charges jusqu'à 600 V. Le dépassement de cette
tension peut endommager le compteur et mettre l'utilisateur en danger. Veuillez
toujours utiliser un transformateur de tension pour des charges supérieures à 600 V.
Le MD Power Meter est un appareil à 600 V avec protection contre les surtensions de
catégorie III.

«
...
9
10
11
12
13
...
»

Содержание MD-P1













































































Отзывы:

Нет отзывов