manualshive.com logo in svg

Siemens MAMMOMAT Novation SP, Руководство по установке, Страница: 33 / 36

Поделиться
Скачать
Siemens MAMMOMAT Novation SP Скачать руководство пользователя страница 33

Siemens AG

SPB7-250.812.03.02.02

MAMMOMAT Novation

08.04

CS SD 24

Cable connections

33

Page 33 of 36

Medical Solutions

Fibre optics cable

0

Handling

0

•

Always handle fiber optic cables delicately and by the connector housing.

•

Avoid acute bends in the cable, as this could break the fiber optic link inside the cable 

Connecting

0

•

Always perform one connection at a time.

•

Remove the dust caps on the fiber optic connectors (you may have to rotate the cap to 
loosen it).

•

Holding the cable by the connector housing, insert the cable connector into the connec-
tor on the device, making sure to align the keying features so the connectors are prop-
erly mated, then turn the connector clockwise to lock it.

•

To disconnect the cable connector, turn it counterclockwise, then pull it from the con-
nector on the device.

Cleaning

0

•

Clean the connectors on both the cable and the devices with a lint-free, alcohol-damp-
ened cloth.

•

Thoroughly wipe the side and end of the ferrule.

•

Blow the ferrule with compressed air, or allow it to air dry, before reconnecting the ca-
ble.

•

Visually inspect the ferrule for lint.

•

When not connected, replace the protective cap onto connector ends.

The DirectRay Interface card is PCI-bus compatible.

Fig. 28: PCI card connection

Pos. 1

RX fiber optic cable (shown with cap on conector)

Pos. 2

TX fiber optic cable

Содержание MAMMOMAT Novation SP





































Отзывы:

Нет отзывов