Siemens M20 Terminal Скачать руководство пользователя страница 170

Страница: 170 / 234

Application notes

Version 8 dated 15.03.00

170

Siemens Information and Communication Products

8.2.10

SMS with M20 to SIM (in text mode)

8.2.10.1

Service centre number

The number of the SC (service center) is provider specific. "A1" and "MAX" are the 2 Austrian network providers.

8.2.10.2

Text mode

8.2.10.3

Send SMS

8.2.10.4

Send SMS to e-mail address

8.2.10.5

Send SMS to fax address

NO CARRIER

Your partner has hung up

ath

To end the connection before your partner

at+csca?

Ask for current SC number

+CSCA: “+43676021”

At the moment connected with SC of Max Mobil

at+csca=”+436640501”

Enter SC number of SIM card (e.g. A1) used at the moment

at+cmgf?

Ask whether the text (1) or PDU (0) mode is used

+CMGF:1

Text mode used

Otherwise change with:

at+cmgf=1

at+cmgs=”+436642254766”

Enter phone number, afterwards: enter

> text of your SMS

Text not longer than..., afterwards: CTRL Z (!)

+cmgs: 27

Counts the messages sent with the SIM card

Enter: ESC to break off the SMS anywhere in the text, without sen-
ding it

e.g. with A1:

at+cmgs=”+43664051”

Enter number depending on the network used, afterwards: enter

>[email protected] (re-
ference) text of your SMS

You have to write (...), afterwards: CTRL Z (!)

+cmgs: 28

Counts the messages sent with the SIM card

NOTE

: A1 will send you a SMS confirming that your SMS was

forwarded to the e-mail address

e.g. with Max Mobil

at+cmgs=”676201170755009”

6762 (Max Mobil), 01 (Vienna), 1707 (Siemens)

> text of your SMS

afterwards: CTRL Z (!)

Содержание M20 Terminal











































































































































































































































Результаты поиска

Содержание M20 Terminal

Отзывы:

Похожие инструкции для M20 Terminal

Бренды по названию

Популярные бренды

Siemens M20 Terminal, Техническое описание

Результаты поиска

Содержание M20 Terminal

Отзывы:

Похожие инструкции для M20 Terminal

Бренды по названию

Популярные бренды