Siemens M20 Terminal Скачать руководство пользователя страница 38

Страница: 38 / 234

AT command interface

Version 8 dated 15.03.00

Siemens Information and Communication Products

ATDS

Dial stored phone number in ME-phonebook

Execute command

ATDS=<n>[;]

Response

TA attempts to set up an outgoing call to stored number.

The phone number is searched in ME-phonebook "ME".

Note:

this command may be aborted generally by receiving a character during execution. This com-

mand cannot be aborted in some connection setup states, such as handshaking.

If there is no valid number

+CME ERROR: <err>

If no dialtone and (parameter setting X=2 or X=4)

NO DIALTONE

If busy and (parameter setting X=3 or X=4)

BUSY

If a connection cannot be set up

NO CARRIER

If successfully connected and non-voice call

CONNECT<text>

Note:

<text> only if parameter setting X>0

TA switches to data state.

When TA returns to command mode after call release

If successfully connected and voice call

Parameter

<n>

address of stored phone number

<;>

voice call

Reference

Siemens

Note

ATE

Enable command echo

Set command

ATE[<value>]

Response

This setting determines whether or not the TA echoes characters received from TE during com-
mand state.

Parameter

<value>

Echo mode off

Echo mode on

Reference

V.25ter

Note

ATH

Disconnect existing connection

Execute command

ATH[n]

Response

Disconnect existing call by local TE from command line and terminate call

Note:

OK is issued after circuit 109 (DCD) is turned off (if it was previously on).

Parameter

<n>

disconnect from line and terminate call

Reference

V.25ter

Note

Содержание M20 Terminal











































































































































































































































Результаты поиска

Содержание M20 Terminal

Отзывы:

Бренды по названию

Популярные бренды

Siemens M20 Terminal, Техническое описание

Результаты поиска

Содержание M20 Terminal

Отзывы:

Бренды по названию

Популярные бренды