Siemens M20 Terminal Скачать руководство пользователя страница 44

Страница: 44 / 234

AT command interface

Version 8 dated 15.03.00

Siemens Information and Communication Products

AT&D

Set circuit Data Terminal Ready (DTR) function mode

Set command

AT&D[<value>]

Response

This parameter determines how the TA responds when circuit 108/2 (DTR) is changed from ON to
OFF during data mode.

Parameter

<value>

TA ignores status on DTR

ON->OFF on DTR: change to command mode while retaining
the connected call

ON->OFF on DTR: disconnect call, change to command mode.
During DTR state = OFF is auto-answer off.

Reference

V.25ter

Note

M1: <value> 0-3

AT&F

Set all current parameters to manufacturer defaults

Execute command

AT&F[value]

Response

TA sets all current parameters to the manufacturer defined profile.

Note:

1) When using AT&F(CR) alone a delay of 300ms needed before next command (AT...) is

sent. Otherwise "OK" response may be corrupted.

2) No restrictions of use of "&F" within a command string. (e.g.:

AT&Fs0=1&W+cbst=7,0,1)

3) A delay of 300ms is needed before next command ist sent, otherwise "OK" response may

be corrupted.

Parameter

<value>

set all TA parameters to manufacturer defaults

Reference

V.25ter

Note

There has to be a pause of at least 300ms after the OK, before the next command is entered.

AT&S

Set circuit Data Set Ready (DSR) function mode

Set command

AT&S<value>

Response

This parameter determines how the TA sets circuit 107 (DSR) depending on the communication
state of the TA interfacing TE.

Parameter

<value>

DSR always on

TA in command mode: DSR is OFF

TA in data mode: DSR is ON

Reference

V.25ter, +IDSR

Note

Содержание M20 Terminal











































































































































































































































Результаты поиска

Содержание M20 Terminal

Отзывы:

Бренды по названию

Популярные бренды

Siemens M20 Terminal, Техническое описание

Результаты поиска

Содержание M20 Terminal

Отзывы:

Бренды по названию

Популярные бренды