Siemens HiPath 3000 V3.0 or later Gigaset M1 Professional страница 111 Скачать руководство пользователя

Страница: 111 / 154

Message functions

101

Step by Step

Checking for a new voice-mail message

either:

Press the message key.

or:

Press and hold down the Talk key or press the Speaker-
phone key.

Call the system menu.

> <

[

Select the menu item and confirm.

Follow the user guidance system from this point on-
wards.

Press the On-hook key to end the operation.

Checking for an old text message

Old messages that have not been deleted cannot be
displayed using the message key

. To call these

messages, proceed as follows:

Press and hold down the Talk key or press the Speaker-
phone key.

Call the system menu.

> <

[

Select the menu item and confirm.

Select the required message and call the additional
menu.

> <

[

Select the menu item and confirm.

> <

Call the additional menu.

[

Select the menu item and confirm. The time of the
message is displayed.

> <

Call the additional menu.

either:

> <

[

Select the menu item and confirm. You call back the
sender.

Menu

Display Messages?

Menu

Display Messages?

Msg. from:
...

Mnu

Text?

<Text>

Mnu

Time/date sent?

at: ...

Mnu

Call Sender?

Содержание HiPath 3000 V3.0 or later Gigaset M1 Professional



























































































































































Результаты поиска

Содержание HiPath 3000 V3.0 or later Gigaset M1 Professional

Отзывы:

Похожие инструкции для HiPath 3000 V3.0 or later Gigaset M1 Professional

Бренды по названию

Популярные бренды

Siemens HiPath 3000 V3.0 or later Gigaset M1 Professional, Руководство по эксплуатации

Результаты поиска

Содержание HiPath 3000 V3.0 or later Gigaset M1 Professional

Отзывы:

Похожие инструкции для HiPath 3000 V3.0 or later Gigaset M1 Professional

Бренды по названию

Популярные бренды