Siemens FLENDER GHDP страница 4 Скачать руководство пользователя | Manualshive

Страница: 4 / 61

background image

BA 5814 en 09/2014

Intended use of Siemens products

Observe also the following:

Siemens products must be used only for the applications provided for in the catalogue and the relevant
technical documentation. If products and components of other makes are used, they must be
recommended or approved by Siemens. The faultfree, safe operation of the products calls for proper
transport, proper storage, erection, assembly, installation, startup, operation and maintenance. The
permissible ambient conditions must be adhered to. Notes in the relevant documentations must be
observed.

Trademarks

All designations indicated with the registered industrial property mark ® are registered trademarks of Siemens AG.
Other designations used in these instructions may be trademarks the use of which by third parties for their own
purposes may infringe holders’ rights.

Exclusion of liability

We have checked the content of the instructions for compliance with the hard and software described.
Nevertheless, variances may occur, and so we can offer no warranty for complete agreement. The information
given in these instructions is regularly checked, and any necessary corrections are included in subsequent editions.

Symbols

Earth connection point

Air relief point

yellow

Oilfilling point

yellow

Oildraining point

white

Oil level

red

Oil level

red

Oil level

red

Connection for
vibrationmonitoring device

Lubrication point

red

Apply grease

Lifting eye

Eye bolt

Do not unscrew

Alignment surface, horizontal

Alignment surface, vertical

These symbols indicate the oillevel checking procedure using the oil dipstick.

These symbols indicate that the oil dipstick must always be firmly screwed in.

«
...
2
3
4
5
6
...
»

Содержание FLENDER GHDP






























































Отзывы:

Нет отзывов

Похожие инструкции для FLENDER GHDP

Relion 670 series

Бренд: ABB Страницы: 66

Бренд: Jacobs Ladder Страницы: 16

Бренд: Quick Страницы: 24

Бренд: JDS Uniphase Страницы: 144

IP Video Test Option HST-3000

Бренд: JDS Uniphase Страницы: 14

Бренд: Kärcher Страницы: 88

APT-9411 Series

Бренд: TAKAYA Страницы: 77

Бренд: Tadano Страницы: 402

Бренд: VelociRAX Страницы: 4

Бренд: ABM Страницы: 17

Бренд: zapco Страницы: 14

Бренд: Teac Страницы: 2

Бренд: ALL-FILL Страницы: 32

ESK+ Manual Knee Lock

Бренд: Blatchford Страницы: 172

Бренд: HEINE OPTOTECHNIK Страницы: 52

Бренд: Ugin Страницы: 39

Бренд: Meritor Страницы: 65

Бренд: Focal Meditech Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды