Siemens FLENDER GHDP Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 61

Siemens FLENDER GHDP Скачать руководство пользователя страница 24

BA 5814 en 09/2014

5.10

Bearingmonitoring system

The gear unit may be fitted with measuring nipples for monitoring the bearings. These nipples are intended
for attachment of shockpulse transducers with rapidaction coupling and are located on the housing in the
vicinity of the bearings to be monitored.

Measuring nipple

SW17

"

X

"

"

X

"

"

X

"

Fig. 9:

Bearingmonitoring system

For a detailed view of the gear unit and the position of the addon parts, please refer to the drawings in the
gearunit documentation.

5.11

Auxiliary drive unit

For certain applications the gear unit can, in addition to the main drive unit, be equipped with an auxiliary
drive unit. This enables the main gear unit to be operated at a lower output speed in the same direction of
rotation. The auxiliary drive is connected with the main gear unit by an overrunning clutch. For the basic
drivetrain configuration refer to figure 10.

Basic design of the gear unit with main and auxiliary drives

7

6

5

2

4

3

1

Fig. 10:

Design of the gear unit with main and auxiliary drives

1

Main motor

4

Main gear unit

7

Output shaft of the main gear unit

2

Auxiliary motor

5

Auxiliary gear unit

3

Coupling

6

Overrunning clutch

The auxiliary gear unit is flanged to the main gear unit by means of an intermediate flange. The auxiliary
gear unit is a MOTOX bevelgear motor coupled to the main gear unit by means of an overrunning clutch.
The overrunning clutch is accommodated within the intermediate flange and is supplied with oil from the
main gear unit. The MOTOX bevelgear motor has its own oil filling.

«
...
22
23
24
25
26
...
»

Содержание FLENDER GHDP






























































Отзывы:

Нет отзывов