Siemens FLENDER GHDP Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 61

Siemens FLENDER GHDP Скачать руководство пользователя страница 17

BA 5814 en 09/2014

4.4.1

Preservation in case of labyrinth seals

Gear units with labyrinth seal are airtight sealed applying the standard preservation with an adhesive tape
on the gap seal of the output shaft. A Vring prevents air exchange on the input shaft.

1

2

3

3

Fig. 5:

Labyrinth seal

1

Vring

3

Air gap

2

Adhesive tape

The adhesive tape must not be removed before startup.

4.4.2

Interior preservation with preservative agent

Before longer periods of storage gear units with forcedlubrication systems, oilcirculation cooling or
noncontacting shaft seals should be filled with preservative agent and run without load.

Table 2:

Durability period and measures for interior preservation when using mineral oil or PAObased
synthetic oil

Duration of protection

Preservative agent

Special measures

Up to

6

months

Castrol Alpha SP 220 S

None

Up to

24

months

- Close all holes on the gear unit.
- Replace the air filter with the plug screw.

(Prior to start-up replace screw plug
with air filter.)

- The labyrinth seal on the output shaft

must be sealed with adhesive tape.
(Prior to start-up this adhesive strip must
be removed.)

1)

For storage periods longer than 24 months, renew the preservative agent (see item 4.4.2.1).

1)

In case of labyrinth seal only (see item 5.7.4)
The input shaft is sealed with a Vring in the area of the labyrinth (see figure 5).

«
...
15
16
17
18
19
...
»

Содержание FLENDER GHDP






























































Отзывы:

Нет отзывов