Siemens FC72x Скачать руководство пользователя страница 59

Страница: 59 / 62

Testing the installation

Checking functions

59 | 62

Building Technologies

A6V10211094_f_en_--

Fire Safety

2015-12-15

8 Testing the installation

The fire detection installation can be switched to 'Test' operation mode to check it

is functioning properly.

8.1 Checking functions

The table below shows the recommended intervals for checking functions. National

specifications always take priority.
For details of the function test, refer to the 'Applicable documents' chapter.

Function

Activity

Interval

(years)

1 2 5

Software

Check date and time.

Detector lines:
● C-NET

Trigger an automatic detector and a manual call point per line.

Trigger all manual call points

Trigger all automatic fire detectors.

Check all detectors for soiling and application.

Check the function of the input/output modules.

On each line check whether short-circuit / open line triggers a 'Fault'.
Check the loop line function.
During short-circuit also check the separator function.

Fire controls

Check activation of the controls up to and with the interface.

Check isolations carried out by the customer. Arrange a time with the

customer.

Degraded function

Mains failure

Check 'Delayed for in case of a mains failure' function.

Alarm organization

Check the function of the delay times t1 and t2.

Alarm activation by automatic detector on 'unmanned'

⇒ Global alarm.

Alarm activation by manual call point on 'manned' and 'unmanned'

⇒ Local alarm/global alarm.

Check automatic switchover 'Manned' / 'Unmanned' on the basis of

the event memory entry.

Check activation of the remote transmission equipment with 'Alarm'. X
Actuate the corresponding danger level by activating a detector with

the detector exchanger and tester

Alarm devices

In emergency power operation check all alarm devices taking the

event category into account:
'Pre-alarm'
'Alarm'
'Fault'

Содержание FC72x































































Результаты поиска

Содержание FC72x

Отзывы:

Похожие инструкции для FC72x

Бренды по названию

Популярные бренды

Siemens FC72x, Краткое руководство пользователя

Результаты поиска

Содержание FC72x

Отзывы:

Похожие инструкции для FC72x

Бренды по названию

Популярные бренды