Siemens FC72x Скачать руководство пользователя страница 19

Страница: 19 / 62

Installation

Power supply - mains voltage connection

19 | 62

Building Technologies

A6V10211094_f_en_--

Fire Safety

2015-12-15

5.2 Power supply - mains voltage connection

When supplied from the factory, the power supply's internal cabling is already

connected.

Power units available

24 V DC/2.5 A, power 70 W, max. battery capacity which can be connected 17 Ah
24 V DC/5 A, power 150 W, max. battery capacity which can be connected 45 Ah

Figure 4: Mains connection in Standard and Comfort housings

1 EMC-critical zone (no high-voltage power permitted)

4 Cable strain relief for mains supply line

Mains connection from below (not permitted when batteries

are fitted)

Mains connection from above

(recommended)

3 Power supply terminals

6 EMC

boundary

● The network cables must be inserted from above.
● The mains lead must be placed along the left side of the housing (observe

EMC zone boundary).

● Signal and control lines must only be fed into the housing on the right from

above or from the rear.

● Batteries must be installed in the correct positions.
● No cable openings should be made in the base of the housing, unless an

additional empty housing is mounted below the station to accommodate the

batteries.

● The mains connection voltage needed (230 V AC/115 V AC) can be found on

the station's type plate.

5 6

3
4

Содержание FC72x































































Результаты поиска

Содержание FC72x

Отзывы:

Похожие инструкции для FC72x

Бренды по названию

Популярные бренды

Siemens FC72x, Краткое руководство пользователя

Результаты поиска

Содержание FC72x

Отзывы:

Похожие инструкции для FC72x

Бренды по названию

Популярные бренды