en
Before using for the first time
12
Notes
¡
If you are using mineral water, set the water hard-
ness range to "very hard". If you are using mineral
water, you must only use non-carbonated mineral
water.
¡
If your tap water is very hard, we recommend that
you use softened water. If you are using only
softened water, set the "softened" water hardness
range.
Setting
Water hardness in
mmol/l
German hardness °dH French hardness °fH
0 (softened)
1
-
-
-
1 (soft)
Up to 1.5
Up to 8.4
Up to 15
2 (medium)
1.5-2.5
8.4-14
15-25
3 (hard)
2.5-3.8
14-21.3
25-38
4 (very hard)
2
Over 3.8
Over 21.3
Over 38
1
Only set this if you will be using solely softened water.
2
Also set for mineral water. Only use non-carbonated mineral water.
7.2 Performing initial start-up
After connecting the appliance to the power supply,
you must configure the settings for its initial start-up. It
may take a few minutes for the settings to appear on
the display.
Note:
You can also use the Home Connect app to con-
figure the settings. When your appliance is connected,
follow the instructions in the app.
1.
Press to switch the appliance on.
a
The first setting appears.
2.
If required, change the setting.
Possible settings:
– Language
– Home Connect
– Time
– Date
– Water hardness
3.
Use
to switch to the next setting.
4.
Work through the settings and make changes as re-
quired.
a
After the last setting, a message appears on the dis-
play confirming that the initial start-up is complete.
5.
To check the appliance before heating for the first
time, open and close the appliance door once.
7.3 Calibrating and cleaning the appliance
before using it for the first time
To ensure that the appliance is automatically calib-
rated, allow the appliance to run empty in steam opera-
tion. Before using the appliance to cook food for the
first time, you must clean the cooking compartment
and accessories.
Note:
The boiling point of water depends on the air
pressure. During the calibration process, the appliance
makes adjustments to adapt to the pressure conditions
in the location where it is installed.
Do not open the appliance door while calibration is in
progress, as this will cancel the calibration process.
Requirement:
The cooking compartment is cold or at
room temperature.
1.
Remove the product information and the accessor-
ies from the cooking compartment. Remove any
leftover packaging, such as polystyrene pellets, and
any adhesive tape that is in or on the appliance.
2.
Wipe the smooth surfaces in the cooking compart-
ment with a soft, damp cloth.
3.
Press to switch the appliance on.
4.
Fill the water tank.
"Filling the water tank", Page 16
5.
Apply the following settings:
Type of heating
fullSteam Plus
Temperature
100 °C
Duration
30 minutes
6.
Start the operation.
‒
Ventilate the kitchen while the appliance is heat-
ing.
a
Calibration starts. This creates a lot of steam.
a
When the time has elapsed, a signal tone sounds. A
message appears on the display confirming that the
operation has finished.
7.
Allow the appliance to cool down and then dry the
cooking compartment floor thoroughly.
8.
ATTENTION!
If there is water on the cooking compartment floor
when operating the appliance at temperatures
above 120 °C, this will damage the enamel.
▶
Do not use the appliance if there is water on the
cooking compartment floor.
▶
Wipe away any water on the cooking compart-
ment floor before operation.
Apply the following settings:
Type of heating
4D hot air
Temperature
Maximum
Duration
30 minutes
9.
Start the operation.
‒
Ventilate the kitchen while the appliance is heat-
ing.
a
When the time has elapsed, a signal tone sounds. A
message appears on the display confirming that the
operation has finished.
10.
Press to switch the appliance off.
11.
Once the appliance has cooled down, clean the
smooth surfaces in the cooking compartment with a
detergent solution and a dish cloth.
12.
Clean the accessories thoroughly using a detergent
solution and a dish cloth or soft brush.
