Steaming
en
17
Reheating
The reheat function can be used to warm up food
that has already been cooked, or bread and pastries
from the day before, without affecting their quality.
Proving dough
Dough proves considerably more quickly using the
dough proving steam heating type than at room tem-
perature and does not dry out.
Defrosting
Use the defrost function to defrost deep-frozen and
frozen products gently without affecting the quality.
Added steam
When you cook with added steam, the appliance intro-
duces steam into the cooking compartment at various
intervals. This gives your food a crispy crust and a
shiny surface. Meat stays juicy and tender, and only un-
dergoes a minimum reduction in volume.
You can combine added steam with the following
functions:
¡
– 4D hot air
– Top/bottom heating
– Circulated air grilling
– Keeping warm
¡
Steam jet
You can use the steam jet function to specifically add
intensive steam at various intervals. This makes bread
and bread rolls in particular wonderfully crispy and
gives them a golden colour.
The appliance adds clouds of steam to the cooking
compartment for approx. 3 to 5 minutes. Depending on
the operation, you can activate the steam jet several
times.
You can add the steam jet for the following functions:
¡
– 4D hot air
– Top/bottom heating
– Circulated air grilling
Note:
Only use the steam jet when cooking compart-
ment temperatures are above 120 °C.
11.3 Setting the type of steam heating
Note:
Observe the instructions for the types of steam heating:
¡
"Types of steam heating", Page 16
Requirement:
The water tank has been filled. If the wa-
ter tank runs dry during operation, a message appears
on the display. Operation is stopped.
"Filling the water tank", Page 16
1.
Press "Steam".
2.
Press the required type of steam heating.
3.
Set the temperature using or , or via the adjust-
ment bar. Or enter the cooking time directly via the
number field .
4.
Press "Cooking time".
A cooking time must always be set for types of
steam heating.
5.
To change the preset cooking time, press the relev-
ant time value, e.g. minute display "min" or second
display "s".
a
The selected value is marked in blue.
6.
Set the cooking time using or , or via the adjust-
ment bar. Or enter the cooking time directly via the
number field .
If required, use to reset the adjustment value.
7.
Press "Apply".
8.
Use
to start the operation.
a
The appliance starts to heat and the time counts
down.
a
When the time has elapsed, a signal tone sounds. A
message appears on the display confirming that the
operation has finished.
9.
Once the cooking time has elapsed:
‒
If required, you can select other settings and re-
start the operation.
‒
When the food is ready, use to switch the ap-
pliance off.
10.
Empty the water tank and dry the cooking compart-
ment.
"After using steam operation", Page 18
Changing the type of steam heating
When you change the type of steam heating, the other
settings are also reset.
1.
Press
.
2.
Press
.
3.
Press the required type of steam heating.
4.
Reset the operation and use
to start.
Changing the temperature
Once the operation has started, you can change the
temperature at any time.
1.
Press the temperature.
2.
Change the temperature using or or via the ad-
justment bar. Or enter the temperature directly via
the number field .
3.
Press "Apply".
Changing the cooking time
You can change the cooking time at any time.
1.
Press the cooking time.
2.
Change the cooking time using or , or via the
adjustment bar. Or enter the temperature directly via
the number field .
3.
Press "Apply".
11.4 Setting added steam
Requirements
¡
Observe the information about the respective operat-
ing mode.
"Setting options with steam", Page 16
¡
The water tank has been filled. If the water tank runs
dry during operation, a message appears on the dis-
play. The appliance continues to operate but without
injecting steam into the cooking compartment.
"Filling the water tank", Page 16
1.
Press the operating mode that you require.
2.
Select the settings for the operating mode, e.g. type
of heating and temperature.
3.
Press "Added Steam" .
4.
Press the required steam level.
