Siemens Cerberus PRO FC721 Скачать руководство пользователя страница 95

Страница: 95 / 118

Commissioning

Detailed commissioning steps

95 | 118

Building Technologies

A6V10211100_f_en_--

Fire Safety

2015-12-15

↑ CPU card

1. Briefly press the 'S8' button on the CPU card until a 'R' is displayed on the LED

matrix display.

2. As soon as the 'R' is displayed, press and hold the 'S8' button for approx. 2 s to

confirm the selection.



A checkmark on the LED matrix display confirms the selection.



The CPU card is restarted.

You will find information on the ↑ CPU card FCC2004, the LED matrix display,

and operating the 'S8' button in document A6V10210368. See chapter 'Applicable

documents'.

10.8 Detailed commissioning steps

In the following chapters, you will find detailed commissioning steps that are

referred to in several chapters.

10.8.1 Preparing 'Station' for commissioning

1. Connect the cables for the ↑ detector lines and the peripheral devices.
2. Connect the power supply (mains and batteries).



The ↑ 'Station' starts and reads in the internal hardware.



During start-up, the 'FAULT' LED flashes and the display shows the

progress.



During start-up, the firmware version F-FXS7211 is displayed.

3. Wait until the display indicates the selection of the ↑ BDV.
4. Press the 'Install' softkey and confirm with the 'Yes' softkey.



The 'Station' restarts.



During this process, the 'FAULT' LED flashes and the display shows the

progress.

5. Wait until only the green 'System On' LED lights up, the display shows the

normal condition, and the 'Station' can be operated.

6. Press <MENU> and select the 'Login/logout' menu item.



You are prompted to enter a PIN.

7. Enter the PIN and confirm with <ok>.



The 'User successfully logged in' message is displayed.



The main menu is shown on the display.

8. Check the firmware of the 'Station' to ensure that it is up to date. To do this,

select the 'Topology' > 'Hardware tree' > 'Station' > 'More Options' > 'Show

details' menu items.



The 'Station' version and configuration data are displayed.

9. Update the firmware if necessary.
10. Enter the date and time. To do this, select the 'Settings/administration' >

'System commands' > 'Set system time' menu items.

Additional messages may be displayed depending on the configuration of the

↑ 'Station'.

Содержание Cerberus PRO FC721























































































































Результаты поиска

Содержание Cerberus PRO FC721

Отзывы:

Похожие инструкции для Cerberus PRO FC721

Бренды по названию

Популярные бренды

Siemens Cerberus PRO FC721, Техническое руководство

Результаты поиска

Содержание Cerberus PRO FC721

Отзывы:

Похожие инструкции для Cerberus PRO FC721

Бренды по названию

Популярные бренды