Siemens Cerberus PRO FC721 Скачать руководство пользователя страница 20

Страница: 20 / 118

Planning
Functions

20 | 118
Building Technologies

A6V10211100_f_en_--

Fire Safety

2015-12-15

4.2 Functions

This chapter describes the most important functions that can be supported by the

fire detection system.

Decision on alarm

The danger signals of the detectors are evaluated by the zone. The decision on

alarm is made at zone level. Decision on alarm can be configured as follows for

each zone:
● Single-detector dependency

– The first detector in the zone which detects the corresponding danger level,

triggers a fire alarm.

● Multi-detector dependency

– The danger levels of several detectors are included in the alarm decision

(e.g. two detectors reporting danger level 3).

Alarm verification concept for delayed alarm transmission

The alarm verification concept (AVC) serves for delayed alarm transmission. The

operating personnel are integrated into the alarming process. During the time (t1)

for monitoring attendance, a check is run to establish whether operating personnel

are present. The operating personnel can examine the fire location during the

investigation time (t2) and can prevent the alerting of the fire brigade in case of

false alarm.
This behavior is only applicable in operation mode 'Manned'.
In operation mode 'Unmanned', the alarm transmission is activated immediately.

An attendance check delay (t1) can be configured for each fire control panel. The

investigation time (t2) can be defined by zone.

Controls

Universal controls can be configured to automatically actuate the appropriate

controls in the event of an alarm. Any events (e.g. alarm or isolation) are linked

logically (OR, AND, NOT) to activate the controls (e.g. the closing of fire doors).

Evacuation

To ensure a controlled evacuation of people from the building in the event of fire, it

is possible to configure chronological alarming in different building sections.

Remote access

The Cerberus Remote Operating Tool provides a PC-based PMI for remote access

to the fire detection system. Remote access to the fire detection system is possible

with the Cerberus Remote Tool. Cerberus Remote is connected to the Ethernet

port of a station.

Содержание Cerberus PRO FC721























































































































Результаты поиска

Содержание Cerberus PRO FC721

Отзывы:

Похожие инструкции для Cerberus PRO FC721

Бренды по названию

Популярные бренды

Siemens Cerberus PRO FC721, Техническое руководство

Результаты поиска

Содержание Cerberus PRO FC721

Отзывы:

Похожие инструкции для Cerberus PRO FC721

Бренды по названию

Популярные бренды