Siemens Cerberus PRO FC721 Скачать руководство пользователя страница 42

Страница: 42 / 118

Installation
Options

42 | 118
Building Technologies

A6V10211100_f_en_--

Fire Safety

2015-12-15

6 Installation

The following installation instructions refer to the specifications of the EN 54

standard and the manufacturer's recommendations. The installation may only be

undertaken by an electrician. Detailed instructions can be found in the system

documentation.
● Use a suitable cable, e.g., NYM 3 x 1.5 mm

(max. 2.5 mm²) or a cable type

with similar performance features to connect the AC voltage from the line

supply.

● The line voltage fuse must be designed for a current level of 10 A.
● The mains connection cable must be routed into the control panel housing from

above or from the rear.

● Provide a suitable mains separator or an appropriately labeled automatic cutout

for the mains voltage connection.

● The nominal voltage required (AC 230 V or AC 115 V) is stated on the control

panel type plate.

● Use a separate residual current unit for residual current circuit breakers.

Depending on the installation conditions, voltage surge protection (primary

protection) is required for the mains connection.

Planning and system limits

Before the installation, check whether the system's planning is suitable for the

system limits. This applies e.g. to all technical data and details of cable lengths,

number of line devices, number of networked stations, battery capacity and

compliance with requirements from standards and national guidelines and local

requirements.
Details of planning can be found in the system documentation.

Information about lightning protection

Further information and detailed specifications relating to producing a lightning

protection concept can be found in the relevant literature and associated

standards.

WARNING

High voltage! Danger to life!
Risk of electric shock
● Mounting and installation work may only be undertaken by qualified staff and

when the system is de-energized.

● Only use cable openings or the edge protection strips provided to protect

cables.

NOTICE

Overvoltage
Damage possible
● Observe the nominal voltage required (AC 230 V) as per the control panel

type plate!

● The fuses used and stated in the factory must not be bypassed or replaced

with any type other than that stated.

● Take appropriate EMC protective measures when handling electronics

modules.

Содержание Cerberus PRO FC721























































































































Результаты поиска

Содержание Cerberus PRO FC721

Отзывы:

Похожие инструкции для Cerberus PRO FC721

Бренды по названию

Популярные бренды

Siemens Cerberus PRO FC721, Техническое руководство

Результаты поиска

Содержание Cerberus PRO FC721

Отзывы:

Похожие инструкции для Cerberus PRO FC721

Бренды по названию

Популярные бренды