Siemens 6RA70 Series, Инструкция по эксплуатации, Страница: 192 / 232

SIEMENS Energy & Automation
10-71
SIMOREG DC Master Base Drive Panel Operating Instructions
PNU
Description Value range
[Unit]
Steps No. indices
Factory
setting
Type See
Change
(Access /
Status)
P696
*
BDS
(G152)
Source for selection of "Stop speed controller I component" function
Selection of binector to control the "Stop I component" function
0 = binector B0000
1 = binector B0001
etc.
When the binector selected in P696 changes to the log. "1" state, the I
component of the speed controller is stopped.
All binector numbers
1 Ind: 2
FS=0
Type: L2 P052 = 3
P051 = 40
Offline
P697
*
BDS
(G153)
Source for selection of enabling of dv/dt injection
Selection of binector to control
enabling of dv/dt injection
(state "1" =
enable)
0 = binector B0000
1 = binector B0001
etc.
All binector numbers
1 Ind: 2
FS=1
Type: L2 P052 = 3
P051 = 40
Offline
P698
*
BDS
(G152)
Source for selection of enabling command for speed-dependent speed
controller PI / P function switchover
Selection of binector to control enabling of the speed-dependent PI / P
controller switchover function (see also P222)
0 = binector B0000
1 = binector B0001
etc.
All binector numbers
1 Ind: 2
FS=1
Type: L2 P052 = 3
P051 = 40
Offline
10.37 Analog inputs (main actual value, main setpoint, selectable inputs)
(see also Section 8, Sheets G113 and G114 of Operating Instructions 6RX1700-0AD** )
Analog input terminals 4 / 5
(main setpoint)
P700
*
(G113)
Signal type of "Main setpoint" analog input
0 = Voltage input 0 to
±
10 V
1 = Current input 0 to
±
20 mA
2 = Current input 4 to 20 mA
0 to 2
1 Ind: None
FS=0
Type: O2 P052 = 3
P051 = 40
Offline
P701
FDS
(G113)
Normalization of "Main setpoint" analog input
This parameter specifies the percentage value which is generated for an
input voltage of 10V (or an input current of 20mA) at the analog input.
The following generally applies:
For voltage input:
P V
Y
X
701 10 [%]
= ∗
X .. Input voltage in volts
Y .. % value which is generated for input
voltage X
With current input:
P mA
Y
X
701 20 [%]
= ∗
X .. Input current in mA
Y .. % value which is generated for input
current X
-1000.0 to 1000.0
[%]
0.1% Ind: 4
FS=100.0
Type: I2 P052 = 3
P051 = 40
Online
P702
(G113)
Offset for "Main setpoint" analog input
-200.00 to 199.99
[%]
0.01% Ind: None
FS=0.00
Type: I2 P052 = 3
P051 = 40
Online
P703
*
(G113)
Mode of signal injection at "Main setpoint" analog input
0 = Injection of signal with sign
1 = Injection of absolute value of signal
2 = Injection of signal with sign, inverted
3 = Injection of absolute value of signal, inverted
0 to 3
1 Ind: None
FS=0
Type: O2 P052 = 3
P051 = 40
Offline
P704
*
(G113)
Source for selection of sign reversal at "Main setpoint" analog input
Selection of binector to control
sign reversal at the analog input
("1" state
= reverse sign)
0 = binector B0000
1 = binector B0001
etc.
All binector numbers
1 Ind: None
FS=0
Type: L2 P052 = 3
P051 = 40
Offline
P705
(G113)
Filtering time for "Main setpoint" analog input
Note: Hardware filtering of approximately 1 ms is applied as standard.
0 to 10000
[ms]
1ms Ind: None
FS=0
Type: O2 P052 = 3
P051 = 40
Online