Siemens 6EP3433-7SB00-0AX0 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 64

background image

Installation

5.2 Output-side connection

SITOP PSU6200 3ph
Equipment Manual, 02.2020, A5E44623402-1-76

33

5.2

Output-side connection

SITOP PSU6200 power supplies provide at their outputs an isolated (= non-grounded) SELV

output voltage (Safety Extra Low Voltage). The output of the power supply is no-load,

overload, and short-circuit proof. If an overload occurs, the electronic current limitation limits

the output current to a maximum value (refer to chapter Technical data (Page 35)).

Figure 5-2

Output-side connection

The output voltage is connected via the "+" and "-" terminals at the output of the power

supply (see Figure Output-side connection (Page 33)). Ensure that the output cables are

dimensioned correctly for the maximum output current rms value and fused accordingly.
The subsequent digit, e.g.: "+1" designates the unique terminal connection, therefore

simplifying correct wiring.

Note
If the safety concept of the plant or system specifies that the DC output circuit should be

grounded (PELV), then it is permissible that the output voltage of the SITOP power supply is

grounded. In this case, ideally, the grounding at the output should be directly connected from

terminal "-" of the power supply to a suitable connection point of the protective conductor

system (PE) of the plant or system.

«
...
31
32
33
34
35
...
»

Содержание 6EP3433-7SB00-0AX0

































































Отзывы:

Нет отзывов

Похожие инструкции для 6EP3433-7SB00-0AX0

Бренд: FAR Страницы: 44

Бренд: FAR Страницы: 28

Бренд: FAR Страницы: 68

Бренд: FAR Страницы: 8

Бренд: PELA Страницы: 8

Бренд: Narex Страницы: 32

FrameSaver 9620

Бренд: Paradyne Страницы: 4

Бренд: Erbauer Страницы: 78

Бренд: Eastwood Страницы: 8

Бренд: MGS Страницы: 38

Green Power HPSB 2524B

Бренд: Pulsar Страницы: 8

Бренд: VOLTEQ Страницы: 5

EPSITRON 787-712

Бренд: WAGO Страницы: 2

CYBERCORE PLATINUM Series

Бренд: XPG Страницы: 50

Бренд: First Choice Страницы: 2

Бренд: Parkside Страницы: 138

Бренд: Stanley Страницы: 10

Бренд: Celltronix Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды