Siemens 6AV7485-6BE00-0AA0 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 47

background image

Installing and connecting the device

3.1 Preparing for installation

IFP2200 INOX MT ETH

18

Compact Operating Instructions, 07/2021, A5E42185570-AD

NOTICE
Damage due to overheating

Inclined installation reduces the convection by the device and therefore the maximum

permitted ambient temperature for operation.
If there is sufficient forced ventilation, the device can also be operated in the inclined

mounting position up to the maximum permitted ambient temperature for vertical

installation. The device may otherwise be damaged and its certifications and warranty will

be rendered null and void.

For information on permitted ambient temperatures, refer to the section Operating

conditions (Page 40).

Mounting position

Select one of the approved mounting positions for your device. The approved mounting

positions are described in the following sections.

Mounting in horizontal format

The device is intended for installation in landscape format.

A maximum ambient temperature of +45 °C is permissible for vertical installation.

Mounting in vertical format

You can also install the device in portrait format.

A maximum ambient temperature of +40 °C is permissible for vertical mounting (0° tilt

angle); a maximum of +35 °C is permitted for inclined mounting.

«
...
16
17
18
19
20
...
»

Содержание 6AV7485-6BE00-0AA0
















































Отзывы:

Нет отзывов

Похожие инструкции для 6AV7485-6BE00-0AA0

Бренд: ABB Страницы: 18

Бренд: R-Tech Страницы: 3

Бренд: Landoll Страницы: 83

Бренд: B. Braun Страницы: 2

Aesculap Neurosurgery

Бренд: B. Braun Страницы: 13

Aesculap AdTec mini

Бренд: B. Braun Страницы: 2

Бренд: B.Well Страницы: 2

Бренд: B. Braun Страницы: 55

BA Ultimate LED

Бренд: B.A. International Страницы: 234

Бренд: Rain-Flo Irrigation Страницы: 16

Бренд: Varytec Страницы: 5

Бренд: Saab Страницы: 98

Бренд: Kaixin Страницы: 89

Бренд: Rath Страницы: 5

Бренд: RBC Bioscience Страницы: 24

Бренд: S&C Страницы: 36

Бренд: S&C Страницы: 15

Бренд: S&C Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды