Siemens 1PQ8 Скачать руководство пользователя страница 96

Страница: 96 / 140

Additional tests may also be required according to the system-specific conditions.

NOTICE
Machine damage
When carrying out the inspection, if you detect any impermissible deviations from the normal

state, you must rectify them immediately. They may otherwise cause damage to the machine.

9.1.5

General inspection

Check that the installation conditions are observed. After approximately 16,000 operating

hours – or the latest after two years – we recommend that the following checks are performed:

Table 9-2

Checks that have to be performed during the general inspection

Checking

When the

motor is

running

At stand‐

still

The electrical parameters are maintained

The permissible bearing temperatures are not exceeded

The smooth running characteristics and machine running noise have not

deteriorated

The foundation has no cracks or indentations. (*)

The machine is aligned within the permissible tolerance ranges.

All the fixing bolts/screws for the mechanical and electrical connections have

been securely tightened

All the potential connections, grounding connections and shield supports are

correctly seated and properly bonded

The winding insulation resistances are sufficiently high (Page 77)

Any bearing insulation is fitted as shown on the plates and labels

The CABLES and insulating parts and components are in good condition

and there is no evidence of discoloring

Condensation can freely flow away.

(*) This check can be made at standstill or when running.

If you detect any deviations during the inspection, you must rectify them immediately. They

may otherwise cause damage to the machine.

Содержание 1PQ8













































































































































Результаты поиска

Содержание 1PQ8

Отзывы:

Бренды по названию

Популярные бренды

Siemens 1PQ8, Инструкция по эксплуатации и установке

Результаты поиска

Содержание 1PQ8

Отзывы:

Бренды по названию

Популярные бренды