manualshive.com logo in svg

Siemens 1PQ8, Инструкция по эксплуатации и установке

Поделиться
Скачать
Siemens 1PQ8 Скачать руководство пользователя страница 126

11.3

Dismantling the machine

Dismantle the machine using the general procedures commonly used in mechanical 

engineering. 

WARNING

Machine parts can fall 
The machine is made up of heavy parts. These parts are liable to fall during dismantling. This 

can result in death, serious injury or material damage. 
● Before you release any machine parts, secure them so that they cannot fall.

11.4

Disposal of components

Components 

The machines consist mainly of steel and various proportions of copper and aluminum. Metals 

are generally considered to be unlimitedly recyclable.
Sort the components for recycling according to whether they are:
● Iron and steel
● Aluminum
● Non-ferrous metal, e.g. windings

The winding insulation is incinerated during copper recycling.

● Insulating materials
● Cables and wires
● Electronic waste

Process materials and chemicals 

Sort the process materials and chemicals for recycling according to whether they are for 

example: 
● Oil
● Grease
● Cleaning substances and solvents
● Paint residues
● Anti-corrosion agent
● Coolant additives such as inhibitors, antifreeze or biocides
Dispose of the separated components according to local regulations or via a specialist disposal 

company. The same applies for cloths and cleaning substances which have been used while 

working on the machine.

Disposal
11.3 Dismantling the machine

SIMOTICS TN Series N-compact  1LH8

126

Operating Instructions 06/2017

Содержание 1PQ8













































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды