manualshive.com logo in svg

Siemens 1PQ8, Инструкция по эксплуатации и установке

Поделиться
Скачать
Siemens 1PQ8 Скачать руководство пользователя страница 58

5.3.5

Aligning the machine to the driven machine and attaching it to it (IM B5)

The standard flange is provided with a centering. The choice of fit for the mating flange on the 

driven machine is the system manufacturer's or the plant operator's responsibility.     

Note
If the machine is not fitted with a standard flange, align the machine to suit the driven 

machine.   

Procedure

The machine axis must be horizontal when it is lifted and the flange must be parallel to the 

mating flange, so as to avoid seizing and stressing. Otherwise damage to the centering will 

result.
1. Grease the centering flange with assembly paste to make the process easier.
2. Screw three studs into tapped holes spaced about 120° apart around the driven machine 

flange. The studs act as positioning aids.

3. Position the machine so that its axis is aligned with that of the driven machine, but not yet 

quite touching. Advance the machine slowly towards the driven machine; advancing too 

quickly risks damaging the centering.

4. If necessary, rotate the machine into the right position so that the clearance holes in the 

flange are central to the tapped holes.

5. Move the machine fully up against the mating flange so that it is fully in contact.
6. Fix the machine using the flange fixing bolts, finishing by replacing the studs.

There is a threaded hole M36 at the bottom of the machine where you can fasten the support 

base.
● Mount the support base so that no additional mechanical tensions can occur in the housing. 

WARNING

Mechanical tensions
The machine may be damaged by additional mechanical tensions in the housing caused 

by incorrect mounting of the support base. The machine or machine parts may loosen 

during operation.
This can result in death, serious injury or material damage.
● Mount the support base so that no additional mechanical tensions can occur in the 

housing.

See also

Tightening torques for screw and bolt connections (Page 131)

Assembly
5.3 Installing the machine

SIMOTICS TN Series N-compact  1LH8

58

Operating Instructions 06/2017

Содержание 1PQ8













































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды