manualshive.com logo in svg

Siemens 1PQ8, Инструкция по эксплуатации и установке

Поделиться
Скачать
Siemens 1PQ8 Скачать руководство пользователя страница 74

Cooling
● Check that the machine cooling is available for commissioning. 

● The water cooling is switched on. The data can be found on the rating plate.
● Cooling water of the configured quality is used.

Electrical connection
● The grounding and equipotential bonding connections have been made correctly.
● The machine is connected so that it rotates in the direction specified.
● Appropriately configured control and speed monitoring functions ensure that the motor 

cannot exceed the permissible speeds specified in the technical data. For this purpose, 

compare the data on the rating plate or, if necessary, the system-specific documentation.

● The minimum insulation resistance values are within tolerance.
● Minimum air clearances have been maintained.
● Any supplementary motor monitoring devices and equipment have been correctly 

connected and are functioning correctly.

● All brakes and backstops are operating correctly.
● At the monitoring devices, the values for "Warning" and "Shutdown" are set.

See also

Set values for monitoring the winding temperature (Page 77)
Setpoint values for monitoring the bearing temperature (Page 77)

7.2

Converter operation

The following chapter is relevant only to machines of series 1PQ8 or if the machine was ordered 

for operation on the rectifier. 

Note
The order number shows whether the machine was ordered for operation with converter: the 

9th digit of the order number features the letter "P" or "Q".

Converter operation
● If the design of the motor requires connection to a particular converter type, the rating plate 

will contain corresponding additional information. 

● The converter is correctly parameterized. The parameterization data is specified on the 

rating plate of the machine. Information about the parameters is available in the operating 

instructions for the converter.

Start-up
7.2 Converter operation

SIMOTICS TN Series N-compact  1LH8

74

Operating Instructions 06/2017

Содержание 1PQ8













































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды