Siebeck FRT-A-SB Series Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 48

Siebeck FRT-A-SB Series Скачать руководство пользователя страница 20

Siebeck GmbH

Translation of the original operating manual

0411 FRT-A-MKIIIbed

Page 20

Inserting the string ( F take-up lever )

When  the  machine  leaves  our  premises,  it  includes  a  piece  of  string
completely  threaded.  Study  the  course  of  the  string  exactly  to  make
understanding  the  following  description  easier.  Proceed  as  follows  in
accordance with the threading diagram opposite:

-Remove the wing nut (B) and the threaded rod (E).
-Insert the threaded rod (E) through the string bobbin (D)
from above.
Place the string bobbin (D) together with the threaded rod (E)
on the bobbin holder (A). Guide the bottom end of the
threaded rod (E) through the drilled hole on the mandrel (C)
and screw on and tighten the wing nut (B). You must make
sure that the string bobbin's cardboard tube rests firmly on
the mandrel (C) and that the net which surrounds the string
bobbin is securely clamped between the cardboard tube and
the mandrel (C).
-Feed the lead end of the string through the drilled hole (F).
-Insert the string in the thread brake (G). Make sure that the
string comes to rest between both pins (H) and the shaft of
the hexagon screw (I) (see figure).
-The next string guides are rollers. Thread the string in
numerical order:

L1 - K2 - L3 - K4 - L5 - K6 - L7 – M

Guide the string through the insert (N) at the end of the tying
arm tube. Inserting the string in the knotting aggregate:
Use your left hand to wrap the string around the twine holder
button  (O)  upwards  from  below.  Use  the  right  hand  to
actuate  the  twine  holder  button  lifting  lever  (P)  in  the
direction of the arrow. Whilst you hold the string tight with
the  left  hand,  the  string  enters  between  the  twine  holder
button  (O)  and  the  twine  holder  button  housing  (R).  The
string  is  clamped  once  you  release  the  twine  holder  button
lifting  lever  (P).  Use  your  right  hand  to  push  the  knife  trap
lever  (S)  forwards  in  the  direction  of  the  arrow;  the  string  is
cut  off.  Close  the  machine  hood,  switch  on  the  master
switch.  After  the  reference  run,  the  machine  is  ready  for
operation.

Check that the string rollers and the take-up lever move freely
and oil them as necessary.

Only use lubricants which are approved for
the food sector (see the chapter
"Maintenance").

«
...
18
19
20
21
22
...
»

Содержание FRT-A-SB Series

















































Отзывы:

Нет отзывов