SIEB & MEYER 0SD4S Series Скачать руководство пользователя страница 23

Страница: 23 / 109

Note

The maximum storage period is 2 years. Electrolytic capacitors produce high leakage

currents when a voltage is applied after a long storage period without applied voltage

and must be reformed. For this purpose, the operating voltage is applied via a 1 kΩ se-

ries resistor for one hour. Please contact the SIEB & MEYER service department for de-

tails.

5.6.2

Installation and Operation

NOTICE

Damage of electrostatically sensitive components due to improper handling

→ Never touch electronic components..

The following requirements are to be considered for the installation and the operation

of the device. Noncompliance with theses requirements is regarded as

abnormal op-

erating condition

Environmental conditions

Operation acc. to IEC 60721-3-3

Place of installation

Switch cabinet installation, indoor, weath-

erprotected, without air conditioning

Climatic conditions

Class 3K3

Temperature range

5 °C to 60 °C (100 % rated current up to max.

40 °C; at higher temperatures the rated cur-

rent must be reduced by 1.5 % per 1 C°.)

Humidity range

5 % RH to 85 % RH (non-condensing)

Degree of pollution acc. to DIN EN

61800-2

Max. site altitude

2000 m above MSL (Units with air cooling only: 100 % rat-

ed current up to 1000 m above MSL; at higher altitudes

the rated current must be reduced by 1.5 % per 100 m.)

Moisture level of human skin

Dry

Chemically active substances

Class 3C1 (no salt spray)

Mechanically active substances

Class 3S1 (no requirement)

Class

Class 3M2

2 to 8 Hz: Amplitude excursion = 1.5 mm

Vibrations

9 to 200 Hz: Amplitude of acceleration = 5 m/s²

Mechanical stability

Shock

Peak acceleration = 40 m/s²

Biological influences

Class 3B1 (no requirement)

UV resistance

No requirement

Tab. 2: Environmental Conditions during Operation

Important

Make sure that the aeration elements are free and open, so that the air circulation is not

restricted.

Drive System SD4S - Hardware Description

Drive Amplifier SD4S

Содержание 0SD4S Series














































































































Результаты поиска

Содержание 0SD4S Series

Отзывы:

Бренды по названию

Популярные бренды

SIEB & MEYER 0SD4S Series, Описание аппаратуры

Результаты поиска

Содержание 0SD4S Series

Отзывы:

Бренды по названию

Популярные бренды