SIEB & MEYER 0SD4S Series Скачать руководство пользователя

Страница: 13 / 109

1. Consider that the mains supply must be protected via an overload release with re-

stricted guidance for each mains phase. The mains line should not be switched on,

before the work is completed.

2. Before turning on the unit the first time, make sure that the connected machine will

not have runaway axes.

3. Never connect capacitive loads to the output phases of the servo amplifiers and fre-

quency converters.

4. Prevent cable loops. Therefore, the units must only be connected to earth at the

provided PE connection for the mains supply line and the racks only at the provided

earth screw.

DANGER

Hazardous voltage

The use of filters causes leakage currents on the protective earth conduc-

tor (PE) which in the event of an error may be considerably higher than the

rated values. To protect persons against dangerous voltages filters must be

connected to earth before they are taken into operation. Possibly a resid-

ual current device cannot be used. According to DIN EN 61800-5-1/ DIN

EN 60204-1 the following measures are required when leakage currents

≥3.5 mA occur:
→ Install a connection without connector on the device and attach a cor-

responding warning note on the device. which also must appear in the

documentation of the device.

→ Use a protective conductor with min. conductor cross-section of

10 mm² or

→ install a second protective conductor: connect it in parallel to the first

protective conductor by using separate terminals.

Operation with residual current device (RCD)

Note

For detailed information regarding the operation with residual current device (RCD) re-

fer to the manual "EMC Guidelines", chapter "Safety-relevant Aspects, Residual Current

Device (RCD)". Also consider the standard DIN EN 60204-1, section 8: additional re-

quirements for electrical equipment with earth leakage currents greater than 10 mA.

3.6

Operation

WARNING

Risk of serious personal injury due to moving machine parts

During the operation of an installation with open doors or removed covers,

persons may seriously be injured by moving machine parts.
→ Keep the doors closed during the operation and do not remove cov-

ers.

Drive System SD4S - Hardware Description

Safety Instructions

Содержание 0SD4S Series














































































































Результаты поиска

Содержание 0SD4S Series

Отзывы:

Похожие инструкции для 0SD4S Series

Бренды по названию

Популярные бренды

SIEB & MEYER 0SD4S Series, Описание аппаратуры

Результаты поиска

Содержание 0SD4S Series

Отзывы:

Похожие инструкции для 0SD4S Series

Бренды по названию

Популярные бренды