Side-Power TP-43A, Инструкция по эксплуатации и руководство пользователя

Страница: 10 / 24

10
Stabilizer Operation and User guide
version 5288-2 - 2018
Alarms and System monitoring
SCU-1x
Fault Code Description Cause Action Boat handling
100.0.0 System Error - - Internal Error -Consult Side-Power dealer L2
201.0.200
NMEA2000 Transmission
parameter - Timeout
No NMEA2000 (pgn127493)
transmission message received for
2seconds.
-Check if GW-1 status is ok
by checking the GW-1 status
LED (See GW-1 user
manual).
-Check cabling L1
10101.0.11
Device CPU Temp - Level
High
CPU temperature higher than 85
degrees.
-Ventilate the room were the
ECU is sitting.
-Consult Side-Power dealer L1
35000.0.200 GPS signal lost - Timeout
No GPS data from GW-1 received for 3
seconds
-Check if GW-1 status is ok
by checking the GW-1 status
LED (See GW-1 user
manual).
- Check cabling L1
40001.0.201
SCU Sensor board fault 1 -
INIT FAIL Sensor board fault. -Consult Side-Power dealer L2
40001.0.202
SCU Sensor board fault 1 -
READ FAIL Sensor board fault. -Consult Side-Power dealer
L2
40002.0.201
SCU Sensor board fault 2 -
INIT FAIL Sensor board fault. -Consult Side-Power dealer L2
40002.0.202
SCU Sensor board fault 2 -
READ FAIL Sensor board fault. -Consult Side-Power dealer L2
40003.0.201
SCU Sensor board fault 3 -
INIT FAIL Sensor board fault. -Consult Side-Power dealer
L2
40003.0.202
SCU Sensor board fault 3 -
READ FAIL Sensor board fault. -Consult Side-Power dealer L2
40004.0.24 PHC-3 - Fault Detected fault on PHC-3
-Check PHC-3 faults for more
information L2
40004.0.100 PHC-3 - No Communication
PHC-3 Communication lost for more
than 500ms
-Check if PHC-3 is powered
and is working
-Check S-Link cabling L2
40004.0.200 PHC-3 - Timeout
PHC-3 startup timed out. Trigger when
startup takes longer than 60 seconds
-Check if PHC-3 is able to
build up the pressure.
-Check PHC-3 faults for more
information. L2
40004.0.210
PHC-3 - DEVICE IN MANUAL
MODE
Trigger when the SCU try to startup PHC-
3 and the PHC-3 is running in manual
mode.
-Stop running the PHC-3 in
manual mode L2
40006.0.24
SCU Sensor board fault 4 -
Fault Sensor board fault. -Consult Side-Power dealer L2
40006.0.150
SCU Sensor board fault 4 -
ID Fault Sensor board fault. -Consult Side-Power dealer L2
40006.0.151
SCU Sensor board fault 4 -
Self-Test Fault Sensor board fault. -Consult Side-Power dealer L2
40006.0.203
SCU Sensor board fault 4 -
Not Calibrated Sensor board fault. -Consult Side-Power dealer
L2
40007.0.100
SCU Sensor board fault 5 -
No Communication Sensor board fault. -Consult Side-Power dealer L2
40007.0.150
SCU Sensor board fault 5 -
ID Fault Sensor board fault. -Consult Side-Power dealer L2
40008.0.24
SCU Sensor board fault 6 -
Fault Sensor board fault. -Consult Side-Power dealer
L2
40009.0.150
SCU Sensor board fault 7 -
ID Fault Sensor board fault. -Consult Side-Power dealer L2
40009.0.151
SCU Sensor board fault 7 -
Self-Test Fault Sensor board fault. -Consult Side-Power dealer L2
40010.0.150
SCU Sensor board fault 8 -
ID Fault Sensor board fault. -Consult Side-Power dealer L2
40011.0.150
SCU Sensor board fault 11 -
ID Fault Sensor board fault. -Consult Side-Power dealer L2
40012.100.51
FCU Current Fin bow port
Current High
Current to the FCU is too high. Trigger
at 10A.
-Check cabling between SCU
and FCU for short circuit. L2
40012.101.51
FCU Current Fin bow
starboard Current High
Current to the FCU is too high. Trigger
at 10A.
-Check cabling between SCU
and FCU for short circuit. L2
40012.102.51
FCU Current Fin stern port
Current High
Current to the FCU is too high. Trigger
at 10A.
-Check cabling between SCU
and FCU for short circuit. L2
40012.103.51
FCU Current Fin stern
starboard Current High
Current to the FCU is too high. Trigger
at 10A.
-Check cabling between SCU
and FCU for short circuit. L2
Page 1