Side-Power SE 60/185 S2 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 24

background image

6

5693

2

2019

-

SE60/185 S2

Propeller Installation

EN

1. Centre the drive pin on the propeller shaft and rotate the shaft, so the pin is in a horizontal state.

2. Insert the propeller onto the shaft and rotate the propeller until the drive pin aligns into the slot/ groove in the propeller.

(NB: Installation requires almost no gap (approximately 1mm) between the propeller and the gear leg.)

3. Insert the washer on the propeller shaft and fasten the propeller lock-nut.

(NB: Ensure the propeller turns freely.)

4. Insert the anode to the end of the propeller and fasten the anode holding screw. Apply a thread glue (Loctite or similar) to ensure that the anode

holding screw does not un-screw itself from during the rotation of the propeller.

MC_0018

!

Please refer to the graphic for special considerations relating to your model

!

MG_0028

Anode holding screw

Anode

lock nut

washer

propeller

drive pin

«
...
4
5
6
7
8
...
»

Содержание SE 60/185 S2

























Отзывы:

Нет отзывов

Похожие инструкции для SE 60/185 S2

Virtex-II Pro ML300

Бренд: Xilinx Страницы: 17

Бренд: IBASE Technology Страницы: 92

Бренд: JETWAY Страницы: 18

Бренд: Texas Instruments Страницы: 47

Бренд: Supero Страницы: 101

Бренд: Energy Страницы: 14

Бренд: BESTEK Страницы: 45

Бренд: Unicorn Computer Страницы: 36

Бренд: Gigabyte Страницы: 64

Бренд: AOpen Страницы: 11

Бренд: Ublox Страницы: 2

D850MV - Desktop Board Motherboard

Бренд: Intel Страницы: 25

Бренд: Texas Instruments Страницы: 33

Бренд: Albatron Страницы: 33

Бренд: Gigabyte Страницы: 80

Бренд: u-blox Страницы: 37

Бренд: TYAN Страницы: 54

Бренд: TYAN Страницы: 62

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды